background image

PATTON MODEL 2715

TABLE OF CONTENTS

Section

Page

1.0 General Information ...............................................................2

1.1 Warranty Statement
1.2 Radio and TV Interference
1.3  CE and Telecommunication Approvals
1.4 Service Information

2.0 General Information........................................................5
2.1 Features
2.2 General Product Description

2.3.1 The 2715 as the Interface between the Telco and CPE
2.3.2 The 2715 as a High-Speed Short Range Modem

2.3 Supported Applications

3.0 Configuration .........................................................................7

3.1 DIP Switch Configuration
3.2  Software Configuration

3.2.1 Introduction to Main Menu
3.2.2 System Configuration
3.2.3 System Diagnostics
3.2.4 Unit Options

4.0 Installation ..........................................................................26

4.1 DTE Interface Connection
4.2 Network Interface Connection
4.3 Power Connection

4.3.1 Using The AC Power Supply (100-240VAC)
4.3.2 Supplying DC Power
4.3.3 Supplying Power via pin KK

5.0 Operation .............................................................................28

5.1 LED Descriptions
5.2 Loop (V.54 & Telco) Diagnostics

5.2.1 Operating Local Loopback (LL)
5.2.2 Operating Remote Digital Loopback (RDL)

5.3  Bit Error Rate (V.52) Diagnostics

Appendix A - Specifications........................................................33           

Appendix B - Cable Recommendations......................................34

Appendix C - Factory Replacement Parts and Accessories ......35

Appendix D - Interface Pin Assignments ....................................36

Appendix E - Power Supply Interface .........................................38

1

1.0  GENERAL INFORMATION 

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is warrant-
ed for One Year parts and labor. If any questions or problems arise
during installation or use of this product, please do not hesitate to con-
tact Patton Electronics Technical Services at (301) 975-1007.

1.1  WARRANTY STATEMENT

Patton Electronics warrants all Model 2715 components to be

free from defects, and will—at our option—repair or replace the product
should it fail within one year from the first date of shipment.This warran-
ty is limited to defects in workmanship or materials, and does not cover
customer damage, abuse, or unauthorized modification. This product
contains no serviceable parts; therefore the user shall not attempt to
modify the unit in any way. If this product fails or does not perform as
warranted, your sole recourse shall be repair or replacement as
described above. Under no condition shall Patton Electronics be
liable for any damages incurred by the use of this product. These dam-
ages include, but are not limited to, the following: lost profits, lost sav-
ings and incidental or consequential damages arising from the use of
or inability to use this product. Patton Electronics specifically dis-
claims all other warranties, expressed or implied, and the installation or
use of this product shall be deemed an acceptance of these terms by
the user. In the event the user detects intermittent or continuous prod-
uct malfunction due to nearby high power transmitting radio frequency
equipment, the user is strongly advised to use only data cables with an
external outer shield bonded to a metal or metalized connector.

2

Summary of Contents for NetLink-E1 2715





















Reviews: