background image

4

1.0  WARRANTY INFORMATION

Patton Electronics

 warrants all Model 2173 components to be free from 

defects, and will—at our option—repair or replace the product should it 
fail within one year from the first date of the shipment.

This warranty is limited to defects in workmanship or materials, and does 
not cover customer damage, abuse or unauthorized modification. If this 
product fails or does not performs as warranted, your sole recourse shall 
be repair or replacement as described above. Under no condition shall 

Patton Electronics

 be liable for any damages incurred by the use of this 

product. These damages include, but are not limited to, the following: lost 
profits, lost savings and incidental or consequential damages arising 
from the use of or inability to use this product. 

Patton Electronics

 spe-

cifically disclaims all other warranties, expressed or implied, and the 
installation or use of this product shall be deemed an acceptance of 
these terms by the user.

Note

Conformity documents of all Patton products can be viewed 

online at www.patton.com under the appropriate product page.

1.1  REGULATORY INFORMATION

EMC Directive:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

• A-tick

Low-Voltage Direcive (Safety):

• IEC/EN60950-1, 2nd Edition

• AS/NZS 60950-1, A-tick

PSTN:

• This device is not intended nor approved for connection to the PSTN

1.2  RADIO AND TV INTERFERENCE (FCC PART 15)

This device generates and uses radio frequency energy, and if not 
installed and used properly-that is, in strict accordance with the manufac-
turer’s instructions-may cause interference to radio and television recep-

Summary of Contents for CopperLINK 2173





















Reviews: