background image

 

4

 

1.0  WARRANTY INFORMATION

 

Patton Electronics

 

 warrants all Model 2168B components to be free 

from defects, and will—at our option—repair or replace the product 
should it fail within one year from the first date of the shipment.

This warranty is limited to defects in workmanship or materials, and does 
not cover customer damage, abuse or unauthorized modification. If this 
product fails or does not performs as warranted, your sole recourse shall 
be repair or replacement as described above. Under no condition shall 

 

Patton Electronics

 

 be liable for any damages incurred by the use of this 

product. These damages include, but are not limited to, the following: lost 
profits, lost savings and incidental or consequential damages arising 
from the use of or inability to use this product. 

 

Patton Electronics

 

 spe-

cifically disclaims all other warranties, expressed or implied, and the 
installation or use of this product shall be deemed an acceptance of 
these terms by the user.

 

Note

 

Conformity documents of all Patton products can be viewed 

online at www.patton.com under the appropriate product page.

 

1.1  REGULATORY INFORMATION

 

EMC Directive:

 

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

 

Low-Voltage Direcive (Safety):

 

• UL60950-1/CSA C22.2 No. 60950-1

• IEC/EN60950-1 2nd Edition

• AS/NZS 60950-1

• A-tick

 

1.2  RADIO AND TV INTERFERENCE (FCC PART 15)

 

This device generates and uses radio frequency energy, and if not 
installed and used properly-that is, in strict accordance with the manufac-
turer's instructions-may cause interference to radio and television recep-
tion. The device has been tested and found to comply with the limits for a 
Class A computing device in accordance with specifications in Subpart B 

Summary of Contents for CopperLINK 2168B





















Reviews: