background image

39

APPENDIX B

CABLE RECOMMENDATIONS

The Patton Model 2500RC Series operates at frequencies of 20kHz

or less and has been performance tested by Patton technicians using
twisted-pair cable with the following characteristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

To gain optimum performance from the Model 2500RC Series,

please keep the following guidelines in mind:

Always use

twisted pair

wire—this is not an option.

• Use twisted pair wire with a capacitance of 20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher
AWG numbers than 26)

• Use of twisted pair with a resistance greater than the above
specifications may cause a reduction in maximum distance
obtainable.  Functionality should not be affected.

• Many environmental factors can affect the maximum distances
obtainable at a particular site.  Use the above data rate/distance
table as a 

general guideline only.

40

APPENDIX C

FACTORY REPLACEMENT PARTS

AND ACCESSORIES

Patton Model #

Description

10-2500RC ......................DDS Cable, RJ48 - RJ48, 6 foot
10-561S...........................Control Port Cable, EIA-561, 6ft, shielded
12M-561 ..........................Adapter, EIA-561 to DB-25 Male
12F-561 ...........................Adapter, EIA-561 to DB-25 Female
082R2..............................Fuse 5x20mm, 200mA, 250V, Time-lag

Little Fuse P/N 239.200

1000RPEM ......................120/240V Rear Power Entry Module
1000RPSM-2 ..................120/240V Front Power Supply Module
1000RPEM-DC................DC Rear Power Entry Module
1000RPSM-48A ..............48V Front Power Supply Module
1000RPEM-V ..................120/240V CE Compliant Rear Power 

Entry Module

1000RPSM-V ..................120/240V CE Compliant Front Power 

Supply Module

0805US ...........................American Power Cord
0805EUR.........................European Power Cord CEE 7
0805UK ...........................United Kingdom Power Cord
0805AUS .........................Australia/New Zealand Power Cord
0805DEN.........................Denmark Power Cord
0805FR............................France/Belgium Power Cord
0805IN.............................India Power Cord
0805IS .............................Israel Power Cord
0805JAP..........................Japan Power Cord
0805SW...........................Switzerland Power Cord

Summary of Contents for 2500RC

















































Reviews: