background image

13

14

4.0  INSTALLATION

The Model 2003 is typically installed by connecting the DB-25 port

to a computer or terminal, the keyboard port to a keyboard, and the
computer port to a computer’s keyboard port. This section describes
connection procedures.

There are three data ports on the rear panel of the Model 2003 --

an RS-232/RS-485 female DB-25 port, a Keyboard port, and a comput-
er port (see Figure 9, below).

4.1  CONNECTING RS-232/RS-485 DEVICES

When the DB-25 port of the Model 2003 is configured as an RS-

232 port, it looks like DCE (Data Circuit-Terminating Equipment).
Therefore, the Model 2003 serial port will connect directly to a DTE
(Data Termination Equipment) The following pinout diagram shows the
signal directions of the pins on the interface.

Pin#

Description

Direction

1

Protective Ground

N/A

2

Transmit Data

RS-232 Input to 2003

3

Receive Data

RS-232 Output from 2003

4

Request to Send

RS-232 Input to 2003

5

Clear to Send

RS-232 Output to 2003

6

Data Set Ready 

RS-232 Output to 2003

7

Signal Ground (common return)

8

Carrier Detect

RS-232 Output from 2003

9

+5VDC

RS-232 Input

14

Transmit Data/Receive Data 

RS-485 Input+/

16

Transmit Data/Receive Data

RS-485 Input-/Output-

20

Data Terminal Ready

RS-232 Input to 2003

4.1.1  Connecting RS-232 Terminal Equipment

The diagrams below show pin connections between the Model

2003's serial port and a standard RS-232 serial interfaces. You may
use these diagrams to construct your own cables, or you may purchase
pre-made cables from Patton Electronics.

PC/XT™ to Model 2003 Pin-Outs

Serial DB-25 (DTE)

Model 2003 DB-25 (DCE)

Pin No.

Pin No.

1 (FG) --------------------------------------- 1 
2 (TD) --------------------------------------- 2
3 (RD) --------------------------------------- 3
4 (RTS) ------------------------------------- 4
5(CTS) -------------------------------------- 5
6 (DSR) ------------------------------------- 6
7 (SG) --------------------------------------- 7
8 (CD) --------------------------------------- 8
20(DRT) ------------------------------------20 

Figure 9. Connection ports on the rear panel of Model 2003

RS - 232 / RS-485

Keyboard

Computer

PC/AT™ to Model 2003 Pin-Outs

Serial DB-9 (DTE)

Model 2003 DB-25 (DCE)

Pin No.

Pin No.

1 (CD)

8 (CD)

2 (RD)

3 (RD)

3 (TD)

2 (TD)

4 (DTR)

20 (DTR)

5 (SG)

7 (SG)

6 (DSR)

6 (DSR)

7 (RTS)

4 (RTS)

8 (CTS)

5 (CTS)

9 (n/c)

Summary of Contents for 2003
















Reviews: