Patton electronics 1180RC User Manual Download Page 13

23

24

APPENDIX D

SPECIFICATIONS

Transmission Format:

Asynchronous or synchronous

Range:

2.5 Km at all data rates, 5 Km at 

specified data rates

Data Rates:

Model 1180RC: aysnc; 0 to 38.4 Kbps 
sync; 2.4, 9.6, 19.2, 38.4, 56, 64, 192 
and 256 Kbps

Model 1184RC: aysnc; DC to 19.2 Kbps
sync; 4.8, 9.6, 14.4, 19.2, 28.8, 32.0,
56.0, 64.0, and 128 Kbps

Interface:

EIA RS-232/V.35 / CCITT V.35 

Transmit Mode:

Single 62.5 or 50 µ core, multi-mode 
fiber cable, Optimal performance is with
62.5 µ cable

Clocking:

Internal, external or Receive Recovered
clock

Handshaking:

Software (X-ON/X-OFF) or hardware 
(RTS/CTS), both modes available at all 
times

Application:

Point-to-point

Typical Link Budget:

8 dB with 50 µ cable; 12 dB with 62.5 µ
cable

Responsivity Minimum:

0.12 A/w

LED Indicators:

TD, RD, RTS, CD, Power, Test

Diagnostics:

Local and remote loopback

Connectors:

DB-25 female (RS-232/V.35), ST or 
SMA (fiber), M/34 female (V.35)

Dimensions:

4.127” W x 1.52 H  x 5.0” L

APPENDIX E

PATTON ELECTRONICS MODEL 1180RC/1184RC

FACTORY REPLACEMENT PART NUMBERS

FRONT AND REAR CARDS

PART NUMBER

DESCRIPTION

1180RC/35/SMA ......................Single-Fiber SRM Rack Card

(M34F/SMA Fiber)

1180RC/35/ST..........................Single-Fiber SRM Rack Card

(M34F/ST Fiber)

1180RC/SMA............................Single-Fiber SRM Rack Card

(DB25F/SMA Fiber)

1180RC/ST ..............................Single-Fiber SRM Rack Card

(DB25F/ST Fiber)

1184RC/35/SMA ......................Single-Fiber SRM Rack Card

(M34F/SMA Fiber)

1184RC/35/ST..........................Single-Fiber SRM Rack Card

(M34F/ST Fiber)

1184RC/SMA............................Single-Fiber SRM Rack Card

(DB25F/SMA Fiber)

1184RC/ST ..............................Single-Fiber SRM Rack Card

(DB25F/ST Fiber)

1000RCM125ST ......................Rear Card (DB25F/ST)

1000RCM125SMA....................Rear Card (DB25F/SMA)

1000RCM134ST ......................Rear Card (M34F/ST)

1000RCM134SMA....................Rear Card (M34F/SMA)

Summary of Contents for 1180RC














Reviews: