background image

19

20

APPENDIX B

PATTON ELECTRONICS MODEL 1094

CABLE RECOMMENDATIONS

The Patton Model 1094 operates at frequencies of 512 kHz or less and
has been performance tested by Patton technicians using twisted-pair
cable with the following characteristics:

Wire Gauge

Capacitance

Resistance

19 AWG/0.9mm 83nF/mi or 15.72 pF/ft.

.0163 Ohms/ft.

22 AWG/0.6mm 83nF/mi or 15.72 pF/ft.

.0326 Ohms/ft.

24 AWG/0.5mm 83nF/mi or 15.72 pF/ft.

.05165 Ohms/ft.

26 AWG/0.4mm 83nF/mi or 15.72 pF/ft.

.08347 Ohms/ft.

To gain optimum performance from the Model 1094 Series, please

keep the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• 

Use twisted pair wire with a capacitance of 20pF/ft or less.

• 

Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher 
AWG numbers than 26).

• 

Use of twisted pair with a resistance greater than the above 
specifications may cause a reduction in maximum distance 
obtainable. Functionality should not be affected.

• 

Many environmental factors can affect the maximum distances
obtainable at a particular site. Use the data rate/distance 
table (below) as a general guideline only.

APPENDIX C

PATTON ELECTRONICS MODEL 1094

FACTORY REPLACEMENT PARTS

AND ACCESSORIES

Patton Model #

Description

0805US ...........................American Power Cord
0805EUR.........................European Power Cord CEE 7
0805UK ...........................United Kingdom Power Cord
0805AUS .........................Australia/New Zealand Power Cord
0805DEN.........................Denmark Power Cord
0805FR............................France/Belgium Power Cord
0805IN.............................India Power Cord
0805IS .............................Israel Power Cord
0805JAP ..........................Japan Power Cord
0805SW...........................Switzerland Power Cord
07M1090SVC ..................Service Manual
07M1094 .........................User Manual

22 AWG 
(0.6mm)

24 AWG 

(0.5 mm)

26 AWG

(0.4 mm)

19 AWG

( 0.9 mm)

384

4.9(7.9)

3.4(5.5)

2.7(4.3) 1.9(3.1)

768

3.1(4.9)

2.2(3.5)

1.8(2.9) 1.3(2.0)

Data Rate

(kbps)

Model 1094 Distance Table in Miles (km)

Wire Gauge 

Summary of Contents for 1094














Reviews: