background image

 

22

 

5.4  LOOPS AND PATTERNS

 

The following section describes the Test Modes used in the Model 1088. At 
the bottom of each Test Mode, a figure is included to show the data path..

 

Figure 14. 

 

Block Diagram Local Loop Mode 1

 

Figure 15. 

 

Block Diagram Local Loop Mode 2

 

Local Loop

 

There are two different modes of operation for a Local Loop 
depending on the status of the units at the time that the Local 
Loop is initiated. If the units are not in linked (NS LED on) and 
the Local Loop is initiated, either by the front panel switch or the 
DTE interface, the unit will enter mode 1. If the units are linked, 
NS LED off, then the unit will enter a mode 2 Local Loop. 

A Mode 1 Local Loop is shown in Figure 14. When the Local 
Loop is initiated, either by the front panel switch or the DTE 
interface, the loop will be activated within the local Processor. 
The data present at the local DTE interface will be looped back 
to the local DTE by the Loop Control block within the Processor. 
Any data present on the line or at the far end DTE interface is 
invalid. The remote unit will remain in the StartUP mode, NS 
LED on, CTS LED yellow, and CD LED yellow, until the local 
unit is taken out of the Local Loop mode. After the Local Loop is 
deselected, the units will both be in StartUP mode and the link 
will be established.

A mode 2 Local Loop is shown in Figure 15. When the Local 
Loop is initiated, either by the front panel switch or the DTE 
interface, two separate loop paths will be started. In the first 
path, data presented to the local DTE interface will be looped 
back to the local DTE within the framer. In the second path,  

Pattern

Gen/Det

Loop

Contr

ol

Loop

Contro

l

Pattern

Gen/Det

Processor

Processor

Framer

Framer

Line

Pattern

Gen/Det

Loop

Contr

ol

Loop

Contro

l

Pattern

Gen/Det

Processor

Processor

Framer

Framer

Line

Summary of Contents for 1088/C

































Reviews: