15
16
Switching the Power Supply On and Off
The power switch is located on the front panel. When plugged in
and switched on, a red front panel LED will glow. Since the Model
1000R16 is a “hot swappable” rack,
it is not necessary for any cards to
be installed before switching on the power supply. The power supply
may be switched off at any time without harming the installed cards.
4.2 INSTALLING THE MODEL 1004ARC INTO THE CHASSIS
The Model 1004ARC is comprised of a front card and a rear card.
The two cards meet inside the rack chassis and plug into each other by
way of mating 50 pin card edge connectors. Use the following steps as
a guideline for installing each Model 1004ARC into the Model 1000R16
rack chassis:
1.
Slide the rear card into the back of the chassis along the metal
rails.
2.
Secure the rear card using the metal screws provided.
3.
Slide the front card into the front of the chassis. It should meet the
rear card when it's almost all the way into the chassis.
4.
Push the front card
gently into the card-edge receptacle of the rear
card. It should “click” into place.
5.
Secure the front card using the thumb screws.
4.3 RS-232 CONNECTION
The RS-232 ports are always the
lower ports on the interface card.
The 10-pin RJ-45 is pinned according Patton's Modified Modular
Interface Standard (based on the EIA/TIA-561Standard). For specific
interface pin-outs, please refer to the diagrams in Appendix D.
(continued)
The Model 1004ARC is wired as a DCE (Data Communications
Equipment). Therefore, it wants to connect to a DTE (Data Termination
Equipment). If your RS-232 output device is a DTE, you may need to
use a special cable (such as a DB-25 to modular cable). If your
RS-232 output device is DCE, you will require a null modem connec-
tion. Call Patton Technical Support at (301) 975-1007 for specific
installation instructions.
4.4 TWISTED PAIR CONNECTION
The Model 1004ARC operates half or full duplex over one or two
twisted pair. In
all applications, the twisted pair wire must be 26 AWG
or thicker, unconditioned, dry, metallic wire. Both shielded and
unshielded wire yield favorable results.
4.4.1 POINT-TO-POINT TWISTED PAIR CONNECTION
The 6-position RJ-11 and 8-position RJ-45 jack options for the
Model 1004ARC (always the
upper jack on the rear interface card) are
prewired for a standard TELCO wiring environment. Connection of a
2-wire or 4-wire twisted pair circuit between two or more Model
1004ARCs requires a
crossover cable as shown in the following charts.
RJ-11
SIGNAL
RJ-45
SIGNAL
1 ...................GND
†
1 ...................N/C
2 ...................RCV-
2 ...................GND
3 ...................XMT+
3 ...................RCV-
4 ...................XMT-
4 ...................XMT+
5 ...................RCV+
5 ...................XMT-
6 ...................GND
6 ...................RCV+
7 ...................GND
8 ...................N/C
†
Connection to ground is optional
NOTE:
Please refer to the Model 1000RP Series User Manual
AC and DC Rack Mount Power Supplies for fuse and power card
replacement information.
NOTE:
Since the Model 1000R16 chassis allows “hot swap-
ping” of cards, it is not necessary to power down the rack when
you install or remove a Model 1004ARC.
NOTE:
The Model 1004ARC can only communicate in a
closed data circuit with another Model 1004ARC. Dial-up analog
circuits, like those in a standard Hayes-type modem, are
not
acceptable. For further information, see Appendix B.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
