Patriot 1900 Instruction Manual Download Page 6

6

NOTE:

If this saw is to be used for com-

mercial logging, a chain brake is required

and shall not be removed or otherwise dis-

abled to comply with Federal OSHA Regula-

tions for Commercial Logging.

SAFETY NOTICE:

Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or

abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel

damage in otherwise healthy people. If

symptoms occur such as numbness, pain,

loss of strength, change in skin color or texture,

or loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek

medical attention. An anti-vibration system

does not guarantee the avoidance of these

problems. Users who operate power tools on

a continual and regular basis must monitor

closely their physical condition and the

condition of this tool.

SPECIAL NOTICE:

Your saw is equipped

with a temperature limiting muffler and spark

arresting

screen

which

meets

the

requirements of California Codes 4442 and

4443. All U.S. forest land and the states of

California, Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington require by

law that many internal combustion engines

to be equipped with a spark arresting screen.

If you operate a chain saw in a state or locale

where such regulations exist, you are legally

responsible for maintaining the operating

condition of these parts. Failure to do so is

a violation of the law. Refer to the SERVICE

section for maintenance of the spark

arresting screen.
Failure to follow all Safety Rules and Precau-

tions can result in serious injury. If situations

occur which are not covered in this manual,

use care and good judgement. If you need

assistance, contact your Authorized Service

Dealer or call 1-800--554--6723.

STANDARDS:

This saw is listed by Under-

writer’s Laboratories, Inc., in accordance with:

ANSI B175.1--2000

American National

Standards for Gasoline--Powered Chain

Saws -- Safety Requirements

CSA Z62.1--1995

Chain Saws -- Occupa-

tional Health and Safety

CSA Z62.3--1996

Chain Saw Kickback Oc-

cupational Health and Safety

ASSEMBLY

Protective gloves (not provided) should be

worn during assembly.

ATTACHING THE BAR & CHAIN

(If not

already attached)

WARNING:

If received assembled,

repeat all steps to ensure your saw is properly

assembled and all fasteners are secure. Al-

ways wear gloves when handling the chain.

The chain is sharp and can cut you even when

it is not moving!

S

Loosen and remove the chain brake nuts

and the chain brake from the saw.

S

Remove the plastic shipping spacer (if

present).

Chain Brake

Chain Brake

Nuts

Bar Tool

Location of shipping spacer

S

An adjusting pin and screw is used to adjust

the tension of the chain. It is very important

when assembling the bar, that the pin located

on the adjusting screw aligns into a hole in

the bar. Turning the screw will move the ad-

justment pin up and down the screw. Locate

this adjustment before you begin mounting

the bar onto the saw. See illustration below.

Adjustment located on Chain Brake

Inside view of

Chain Brake

S

Turn the adjusting screw by hand counter-

clockwise until the adjusting pin just

touches the stop. This should allow the pin

to be near the correct position.

S

Slide guide bar behind clutch drum until

guide bar stops against clutch drum

sprocket.

Mount the Bar

S

Carefully remove the chain from the pack-

age. Hold chain with the drive links as

shown.

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Tip of

Bar

Summary of Contents for 1900


















Reviews: