2
3
IMPORTANT SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
PREPARATION
Before beginning assembly, installation or operation of product, make sure all parts
are present. Compare parts with package contents list and diagram on previous page.
If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Slotted Screwdriver, Phillips Screwdriver,
Pliers, Electrical Tape, Wire Cutters, Safety Glasses, Ladder, Wire Stripper, Weather
Resistant Caulk
2. Firmly attach the fixture ground wire
(bare copper) to the mounting bracket with
the ground screw (by wrapping around
the ground screw) and then connect it to
the house supply ground wire with a wire
nut (AA). Connect the black wire from the
fixture (A) to the black wire in the electrical
box and connect the white wire from the
fixture (A) to the white wire in the
electrical box. Use supplied wire nuts (AA)
for all wire connections.
3. Once connections of wires are completed,
carefully tuck wires and wire nuts (AA) into the
electrical box making sure no bare wire (on
the black and white) is visible at the wire nuts
(AA). Position hole in fixture (A) over nipple and
secure in place with star washer (EE) and cap
nut (DD).
6. After installation, seal around the perimeter
between the fixture (A) and the ceiling or wall
surface with weather resistant caulk (not included).
4. Install the proper bulb type and wattage
(not included).
A
A
B
C
White
Black
House
supply
Ground
wire
Fixture
Ground wire
AA
Ground
Screw
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
Please save this instruction manual.
WARNING
• Turn off electricity at main fuse box (or circuit breaker box) before beginning
installation by removing fuse (or switching off circuit breaker). Do not remove
insulation from fixture.
• Be careful not to damage or cut the wire insulation (covering) during fixture
installation. Do not permit wires to contact any surface having a sharp edge.
To do so may damage or cut the wire insulation, which could cause serious
injury or death from electric shock.
• This product must be installed in accordance with the applicable installation
code by a person familiar with the construction and operation of the product and
the hazards involved.
• CAUTION – RISK OF FIRE. Consult a qualified electrician to ensure correct
branch circuit conductor.
• Firmly attach the fixture ground wire (bare copper) to the mounting bracket with
the ground screw (by wrapping around the ground screw) and then connect it to
the house supply ground wire with a wire nut.
CAUTION
• All electrical connections must be in agreement with local codes, ordinances or
the national electric code (NEC). Contact your municipal building department to
learn about your local codes, permits and/or inspections.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC.
Consult a qualified electrician before installation.
• Do not connect this fixture to an electrical system that does not provide a means for
equipment grounding. Never use a fixture in a two-wire system that is not grounded.
If you are not sure your lighting system has a grounding means, do not attempt to
install this fixture. Contact a qualified, licensed electrician for information with regards
to proper grounding methods as required by the local electrical code in your area.
• If a dimmer control switch is used with this fixture, obtain professional advice to
determine the correct type and electrical rating required.
Nipple
DD
EE
FF
Bulb
Electrical
Box
CC
BB
1. Attach nipple to mounting bracket (BB).
Adjust so it will clear hole in back of fixture
and then lock nipple in place with hex nut.
Attach mounting bracket to electrical box
with electrical box screws (CC).
Nipple
Hex nut
5. Position glass (B) inside guard (C) and place
on fixture (A). Secure in place with two
screws (FF) and tighten until gasket seals.
Weather
Resistant
Caulk