Pass Pass X5 Owner'S Manual Download Page 7

7

X5 Owner’s Manual

All figures obtained after a 1 hour warmup, with regulated 120 VAC 
power line.  See manual notes about AC power line regulation.

Gain   
Freq. Response 
Power Output   

Maximum Output Voltage 
Maximum Output Current 
Input Impedance

Damping factor 
Slew rate 
Output Noise

Balanced CMRR
DC offset 
Power Consumption 
Dimensions  
Weight 

30 dB
0 dB at DC, -3 dB at 100 kHz
125 X 5 watts maximum @ 1% THD,

 

1 kHz, 8 ohms
plus, minus 50 volts
plus, minus 10 amps

22 kohm balanced, 11 kohm

 

unbalanced

200 ref  8 ohms nominal

approx. 

plus, minus 50 V/uS

 

approx.

 

approx. 

300 uV unweighted 20-20

 

kHz

approx. -

85 dB @ 1 kHz

< 100 mv
200 watts idle,  600 watts maximum

 

19 “ W  x  7” H x  20” D

85

 lbs.

For more information please contact:

Pass Laboratories Inc.

P.O. Box 219,
24449 Foresthill Rd.,
Foresthill, CA 95631

Tel: 530.367.3690
Fax: 530.369.2193

www.passlabs.com

© 2006, Pass Laboratories Inc.

X5 Specifications

“Pass”, “

pass

”, “Pass Labs”, “Pass Laboratories”, Supersymmetery”, 

“Aleph”, and “Zen” and are all registered trademarks of  Pass 
Laboratories, Inc., and all rights thereto are protected by law.

Summary of Contents for Pass X5










Reviews: