background image

7

XP-12_om_10.17

BALANCE: Pressing balance left (<) or balance right (>) will increase 

the level in the left or right speaker, depending upon which button 

is pushed.

VOLUME:  Pressing the increase (^) button or the decrease (v) 

button will shift the volume setting 1dB, holding a button down will 

increase or decrease the level until such time as you either release 

pressure on the button or reach the limits of the volume control.

PASS THRU:  Pushing this button twice, sets the pre-amplifier to 

volume step 89 (0 dB) and input 5.   As an added precaution when 

“pass through” is selected the volume ramps upto 89. 

 

This is to prevent nasty surprises when “pass thru” is selected 

accidentally. The ramp up sequence can be stopped at any time 

by hitting any button on the remote.

The button must be pressed again to exit “Pass Thru” and unlock 

the other command selections.

DISPLAY:  The default setting for the display is “bright”, pressing 

the display button once changes the display to its “dim” or “low 

intensity” setting, pressing the button a second time selects “off” 

for the display.  When “off” is selected any other control function 

will cause the display to indicate product operational status for 

approximately 7 seconds and then the display will once again 

blank.  Pressing the display button a third time cycles back to a 

“bright display”

We recommend the use of the balanced output mode where 

possible.  Balanced input to power-amplifiers will typically retain the 

character of the input mode, but offers less distortion, less noise, 

more gain, and more voltage swing, without compromising the 

sound.

With balanced operation, the common mode rejection of the 

preamp reflects the intrinsic common mode rejection of the 

topology, the matching of the gain devices, and the matching of 

the attenuator channels.  In this case we have been able to keep 

the total mismatch to about .1%, for a common mode rejection of 

approximately  -60 dB.

The input system of the preamplifier will exhibit full common 

mode noise rejection with passive balanced sources, where the 

negative input is connected to ground at the source through 

the appropriate source impedance.  This allows adaptation of 

unbalanced sources to balanced operation with passive cable 

connections in a manner that achieves the noise rejection of active 

balanced sources.

Summary of Contents for XP-12











Reviews: