background image

9

XA200.5 Owner’s Manual

the temperature exceeds 75 degrees Centigrade.  This thermal cutout 
should never occur in real life.  This is a very rare occurrence, and 
would indicate a serious problem.

Interconnects and Speaker Cables

 We have a general recommendation about interconnects, and 
speaker cables:  They should cost less than the amplifier, and contain 
at least some conductive material.  We have tried a lot of  products 
and most work well, but as a practical matter we cannot make blanket 
recommendations.  

The amplifier is not sensitive to source interconnects.  It is also not 
sensitive to radio frequency pickup, which allows some flexibility in 
choosing source interconnects without shields, though shields are 
usually a very good idea.  For long runs balanced cables are highly 
recommended for their inherent rejection of  noise.

 We prefer speaker cables that are short and stout.  Oxygen-free 
copper and silver are the suggested materials.  If  you find any really 
exceptional cable made of  gold, please gift us a couple hundred feet.

Fortunately this amplifier is not sensitive to the capacitive/inductive 
character of  some of  the specialty speaker cables, so feel free to 
experiment.

We have found that about 90 per cent of  bad sounding cables are 
really bad sounding connections, and we recommend that attention 
be paid to cleanliness of  electrical contact surfaces and proper 
connector fit.

Speaker cables should be firmly tightened down at the speaker 
output terminals, but not with a wrench.  Output terminals will not 
withstand the levels of  torque that may be easily applied by wrench.  
Hand tightening without excessive force is plenty.  Cleaning contact 
surfaces with one of  the commercially available electronic contact 
cleaners should be part of  your annual system maintenance.

Product Life

So how long will this hardware last?  It is our experience that, barring 
abuse or the odd failure of  a component, the first things to go will be 
the power supply capacitors, and from experience, they will last 15 to 
30 years.  Fortunately they die gracefully and are easily replaced by a 
good technician.  

Summary of Contents for XA200.5














Reviews: