manualshive.com logo in svg

Paso T3015DMA, Installation Manual And Operating Instructions, Page: 17 / 32

Share
Download
Paso T3015DMA Installation Manual And Operating Instructions Download Page 17

PROFESSIONAL AUDIO & SOUND

®

TM

DIGITAL MUSIC SERIES

DIGITAL MUSIC AMPLIFIERS

INSTALLATION AND WIRING

PAGE 17

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

T3015/3030DMA

REMOTE MASTER VOLUME
The Amplifier features a Remote Volume Control Input. A
50 KB Potentiometer and Knob are supplied with the
Amplifier. Mount the Control on a suitable Wall Plate or any
other convenient surface and connect to the Amplifier
REMOTE VOLUME Terminals as shown in the Diagram.

OPERATION
The Control is a Master Volume and controls all the 3
Inputs of the Amplifier with the exception of the MOH and
ZONE 1 and ZONE 2 Outputs.

CABLE
To connect the Remote Control to the Amplifier use a two
conductor wire not less than AWG 24. While the Remote
Volume System uses DC rather than audio caution should
be exercised in the layout of the wire. Always avoid routing
next to power lines. If the total wire resistance exceeds 3 K
ohm the Volume may not go down to zero.

REMOTE MASTER VOLUME

REMOTE MASTER VOLUME CONTROL

INPUT 1

RVC

MIC/TEL

REM

VOLUME

BALANCED

REMOTE

VOL

HOT

G

COM

REMOTE VOL

CONTROL

50 KB

REMOTE VOLUME CONTROL

OTENTIOMETER IS SUPPLIED

WITH THE AMPLIFIER.

3015B Remote Volum

Fig. 17 - Remote Volume Control Connection Diagram

POWER SUPPLY
The Amplifier provides a 24 Volt DC Regulated Auxiliary
Power Supply Output at 100 mA current.

CABLE
To connect the Power Supply Output to accessories use a
two conductor wire not less than AWG 18. This minimum
wire gauge is necessary to minimize potential Voltage
Drops in long wire connection applications. For wire resist-
ance refer to Table below.
CAUTION: Be sure that the 24 V DC Output Terminals are
not shorted during installation.

24 VOLT POWER SUPPLY

REGULATED AUXILIARY POWER SUPPLY

NC

NO

C

+

-

0

0

0

RELAY

VOX

24V DC
100 mA

1 WATT

ZONE 2

ZONE 1

1 VOLT

8

OHM

8

OHM

600

OHM

Fig. 17B - 24 Volt Power Supply Output Diagram

WIRE GAUGE - RESISTANCE TABLE

WIRE

RESISTANCE IN

AWG

OHMS per 1000 Ft.

16

4.016

18

6.385

20

10.15

22

16.14

24

25.67

26

40.81

NOTE:
When calculating the Wire
Resistance for each run using a
two conductor Wire the wire
Resistance should be doubled.

EXAMPLE: The Total Resistance
of a 1000 Ft. run of a AWG 24 two
conductor Wire is:

25.67 X 2= 51.34 Ohm

Summary of Contents for T3015DMA

































Reviews:

No comments