manualshive.com logo in svg

Paslode IM250 F-16 II, Operating Manual, Page: 15 / 20

Share
Download
Paslode IM250 F-16 II Operating Manual Download Page 15

14

Fasteners and Applications

Applications

The Paslode Cordless Finish nailer is suited for a variety of applications.  Some of these are securing trim to door and
window casings; attaching baseboards where walls meet floors; attaching moldings where walls meet ceilings;
securing paneling; securing chair rails, picture molding and other decorative trim.

The Paslode Cordless Finish nailer drives Paslode F-16 Series  nails.  They are made from 16-gauge galvanized wire and
are entirely coated witrh Pas-Kote for improving holding power.  Fasteners are collated into strips of 50 for easy loading.

Fasteners

PART

NO.

      SIZE

                TYPE

095201

F16          3/4"

Panel, Bead Molding*

095203

F16            1"

Panel, Cap/Shoe Molding*

095205

F16       1-1/4"

Cap/Shoe Molding*

095257

F16      1-1/2"      Baseboard, Crown, Chair

095435

F16       1-3/4"

Baseboard, Crown , Chair

095436

F16            2"

Baseboard, Casings, Crown

400601

F16      2-1/4"

Casings

090025

F16      2-1/2"

Casings

THE CORDLESS FINISH 

 

NAILER DRIVES THESE NAILS

                                                                   * May require back plate insert (provided with tool) to drive these fasteners.

Summary of Contents for IM250 F-16 II





















Reviews:

No comments