background image

13

Cordless Stapler Operation

Depth of Drive Adjustment

Remove the battery  before adjusting the depth of drive.

The depth of drive adjustment is made by simply loosening
the 3/8" hex nut, adjusting to desired depth and retightening
the hex nut.

Dual Function of the Work Contacting
Element:

The Cordless Stapler has the unique feature of a dual
function contacting element.
For Siding Applications:
Loosen the 3/8" hex nut and adjust the work contacting
element up or down for staple standing height. 

(see above

picture)

For Sheathing Applications:
Remove the 3/8" hexnut.
Remove the work contacting element.
Turn the work contacting element upside down
Replace the washer and tighten the hex nut down.

PRESS WORK –
CONTACTING
ELEMENT
AGAINST THE
WORK SURFACE.

Fan motor starts,
fuel is injected into
combustion
chamber and
mixed with air by
the fan.

SQUEEZE
TRIGGER
Spark plug sparks
and fuel/air mixture
ignites.
Combustion
powers piston
assembly driving
fastener.

LIFT TOOL -
RELEASE
TRIGGER
Combustion
chamber opens.
Fan exhausts hot
gases and cools
internal
components.

2

           DANGER

The work contacting element and nose will become hot
after prolonged or rapid use. If it becomes necessary to
adjust the work contacting element, avoid touching with
bare hands.

NOTE

The stapler will "blank fire" or cycle even if the
magazine is empty of nails.  Blank firing will create
driver blade marks on the workpiece, and excessive
impact on the bumper which may result in premature
failure of the bumper.Therefore, load the Cordless
Stapler when required and only cycle it when staples
are in place.

Summary of Contents for IM200/50 S16





















Reviews: