Partner T250 Instruction Manual Download Page 10

10

TROUBLE

CAUSE

REMEDY

Engine will not

start.

1. ON/OFF switch in OFF

position.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

6. Carburetor requires

adjustment.

1. Move ON/OFF switch to ON position.

2. See “Starting a Flooded Engine” in

Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

6. Contact an authorized service dealer.

Engine will

not idle

properly.

1. Carburetor requires

adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. See “Carburetor Adjustment” in

Service and Adjustments Section.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

5. Compression low.

Engine will not

accelerate,

lacks power,

or dies under

a load.

1. Clean or replace air filter.

2. Clean or replace plug

and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

Engine

smokes

excessively.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact an authorized service dealer.

Engine runs

hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

1. Empty fuel tank and refill with

correct fuel mixture.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

WARNING:

Always stop unit and disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

DECLARATION OF CONFORMITY

relating to 2000/14/EC

EU Declaration of Conformity relating to 2000/14/EC

We,

Poulan/Weed Eater Division, Electrolux Home Products, Inc.,

Texarkana, TX,

75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the

Partner

model T250 grass trimmer

was assessed in accordance with Annex V of the DIRECTIVE

and from serial numbers 2001--305N00001 and onwards, conforms to the provisions of the

DIRECTIVE. The cutting width is 431 mm. The measured sound power is 107 dB and the

guaranteed sound power is 112 dB.
Texarkana 01--12--17

Michael S. Bounds, Director

Product Safety and Standards

Summary of Contents for T250












Reviews: