manualshive.com logo in svg

Partner P33XT, Instruction Manual, Page: 2 / 15

Share
Download
Partner P33XT Instruction Manual Download Page 2

2

IDENTIFICATION (WHAT IS WHAT?)

Chain

Adjustment Tool

(Bar Tool)

Primer Bulb

Fuel Mix Fill Cap

Starter
Housing

Bar Oil
Fill Cap

Chain

Front Hand Guard

Front Handle

Starter Rope

ON/STOP
Switch

Muffler

Idle Speed Screw

Bumper
Spike

Bar Guard

Guide Bar

Chain Brake Nuts

Cylinder Cover

Throttle
Lockout

Rear
Handle

Throttle
Trigger

Choke/
Fast Idle
Lever

Chain
Brake

Chain
Direction
of Travel

Adjusting
Screw

Chain
Catcher

Bar
Sprocket
Hole

IDENTIFICATION OF SYMBOLS

WARNING!

This chain

saw can be dangerous! Care-
less or improper use can cause
serious or even fatal injury.

Read and understand the
instruction manual before
using the chain saw.

Always use two hands when operating the chain saw.

WARNING!

Contacting the guide bar tip with any object

should be avoided; tip contact may cause the guide bar to
move suddenly upward and backward, which may cause se-
rious injury.

Always wear appropriate ear
protection, eye protection
and head protection.

Sound power level

Summary of Contents for P33XT
















Reviews:

No comments