manualshive.com logo in svg

Partner K950 CHAIN, Workshop Manual, Page: 12 / 18

Share
Download
Partner K950 CHAIN Workshop Manual Download Page 12

CLUTCH

6

11

Lubrication duct

Check that the lubrication
duct for the clutch drum’s
needle bearing is open. 
Clean if blocked.

Lubrication duct

Check that the lubrication duct for
the clutch drum’s needle bearing is
open. If it is blocked, clean it with
steel wire.

Fit the clutch

Text facing out

Fit the clutch with the side featuring
the word “Off” facing out.

Counter-clockwise for installation

Turn the clutch counter-clockwise by
hand until it bottoms.

Fit the clutch

Text facing out

Fit the clutch with the side 
featuring the word “Off”
facing out.

Counter-clockwise for
installation

Rotate the clutch counter-
clockwise by hand until it 
bottoms.

Tighten the clutch

Piston stopper 502 54 15-01 must be
in the spark plug hole.

Use tool 502 54 04-02 to tighten the
clutch. Rotate the tool counter-clock-
wise. The correct tightening torque is
30–40 Nm.

Tighten the clutch

The piston stopper must be
in the spark plug hole.

Turn the special tool counter-
clockwise, tightening torque
30–40 Nm.

Refitting

Remove the piston stopper.

Refit the spark plug and air filter.

Lubricate the clutch drum’s needle
bearing with oil and put the clutch
drum in place.

Fit the chain, bar and cover.

Adjust chain tension according to the
instructions in the previous chapter.

Refitting

Remove the piston stopper.

Refit the spark plug and air 
filter.

Lubricate the clutch drum’s
needle bearing with oil, then
install.

Fit the chain, bar and cover.

Adjust chain tension.

Summary of Contents for K950 CHAIN



















Reviews:

No comments