Parrot Uncle BBCF444 Owner'S Manual Download Page 26

26

13. Accessories

Do  not  use  water  when  cleaning  your  ceiling  fan. 

It could damage the motor or the blades and create the 

possibility of an electrical shock.

 

WARNING

!

IMPORTANT CARE INSTRUCTIONS 

for your Ceiling Fan

Periodic  cleaning  of  your  new  ceiling  fan  is  the  only 

maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to 

avoid scratching the finish.
Abrasive  cleaning  agents  are  not  required  and  should 

be avoided to prevent damage to finish.

12. Maintenance

11. Using Your Ceiling Fan

REVERSE 

SWITCH

FAN MOTOR 

ASSEMBLY

   Figure 38

11.1

Restore  Electrical  Power  to  the  Outlet  Box  by  turning 

the Electricity on at the Main Fuse Box.
During  Summer  Months,  run  the  Fan  Counter-

Clockwise,  as  you  look  up  at  it,  to  direct  airflow 

downward.
During  the  Winter  Months,  run  the  Fan  Clockwise,  as 

you look up at it, to direct airflow upward.
If  airflow  is  desired  in  the  opposite  direction,  turn  the 

Ceiling Fan off and wait for the Blades to stop turning.
Slide  the  Reverse  Switch  (located  on  top  of  the  Fan 

Motor Assembly) to the opposite position, and turn the 

Ceiling Fan on again (Figure 38).
The  Fan  Blades  will  turn  in  the  opposite  direction  and 

reverse the airflow.

Reverse Switch Information

Season 

Blade Rotation Direction 

Summer 

Counter-Clockwise 

Winter 

Clockwise 

Summary of Contents for BBCF444






























Reviews: