10 GB/CY
Before use
Mounting / replacing
saw blades
WARNING!
Pull the mains plug out of the
mains socket before you carry out any task on the
device. Failure to observe this advice may lead to
injury.
Turn the quick-release chuck
7
and hold it in
the turned position.
Press the selected saw blade up to the stop
into the quick-release chuck
7
. The saw blade
should engage.
Release the quick-release chuck
7
. The chuck
must then return to its original position. The saw
blade is now locked in place.
Rotating the hand grip
WARNING!
DANGER OF INJURY!
Pull
the mains plug out of the socket before you carry
out any task on the device, The hand grip
4
can
be rotated by 90° to the right or left. This allows
the ON / OFF switch
3
to be brought into the most
comfortable position for any working conditions.
Press the unlocking button
10
and rotate the
hand grip
4
to the right or left.
Make sure the hand grip
4
engages.
Adjusting the shoe
WARNING!
DANGER OF INJURY!
Pull
the mains plug out of the socket before you carry
out any task on the device,
Adjust the shoe
5
to suit the cutting depth.
To do this release the shoe adjustment lever
8
and place the shoe
5
in appropriate position.
Lock the shoe in this position by pulling the
shoe adjustment lever
8
tight.
Setting the blade speed
The desired blade oscillation speed can be prese-
lected by using the setting wheel
1
(MIN. = lowest
oscillation speed, MAX. = highest oscillation speed).
The blade speed can also be selected whilst you
are using the device.
Preparing for use
Switching on and off
When operating the device you can select between
intermittent or continuous operation mode.
To switch on intermittent operation mode:
Press the ON / OFF switch
3
.
To switch off intermittent operation mode:
Release the ON / OFF switch
3
.
To switch on continuous operation mode:
Press the ON / OFF switch
3
and fix it in the
pressed position with the lock button
2
.
To switch off continuous operation mode:
Press the ON / OFF switch
3
and release it
again.
Guiding the sabre saw
safely and accurately
The shoe
5
pivots to adjust to the workpiece and
provides safe support to the device. It must always
lie against the workpiece when the device is in use.
Advice about ways of
working when sawing
Before sawing, check the workpiece for foreign
bodies such as nails, screws etc. and remove them.
Before use / Preparing for use
Summary of Contents for SABRE SAW PFS 710 A1
