Parkside PZKS 2000 A1, Operating And Safety Instructions, Translation Of Original Operating Manual

Page: 57 / 68

52 GB
• Move the machine head (4) to its upper position.
• Use the handle (1) to push back the machine head (4) and fix
it in this position if required (dependent on the cutting width).
• Place the piece of wood to be cut at the stop rail (16) and
on the turntable (14).
• Lock the material with the clamping devices (7) on the fixed
saw table (15) to prevent the material from moving during
the cutting operation.
• Release the lock switch (3) and press the ON/OFF switch
(2) to start the motor.
• With the drag guide (21) fixed in place (21) :
use the handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw blade (6)
has completely cut through the work piece.
• With the drag guide (21) not fixed in place (21):
pull the machine head (4) all the way to the front. Lower the
handle (1) to the very bottom by applying steady and light
downward pressure. Now push the machine head (4) slowly
and steadily to the very back until the saw blade (6) has
completely cut through the work piece.
• When the cutting operation is completed, move the machine
head back to its upper (home) position and release the ON/
OFF button (2).
Attention! The machine executes an upward stroke auto-
matically due to the return spring, i.e. do not release the han-
dle (1) after completing the cut; instead allow the machine
head to move upwards slowly whilst applying light counter
pressure.
8.4 Crosscut 90° and turntable 0° - 45° (fig.
1/7/8)
The crosscut, drag and mitre saw can be used to make cross-
cuts of 0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
Important! For 90° crosscuts, the moveable stop rail (16a)
must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
• The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
• Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen the handle (11) if tightened, pull up the latched posi-
tion lever (35) with your index finger and use the handle
(11) to set the rotary table (14) to the desired angle.
• The pointer (12) on the rotary table must match the desired
angle on the scale (13) on the fixed saw table (15).
• Re-tighten the handle (11) to secure the rotary table (14).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/5/9/10)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (23).
• Fix the rotary table (14) in the 0° position.
Attention! For mitre cuts (inclined saw head), the left side of
the moveable stop rails (16a) must be fixed in the outer posi-
tion.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a maxi-
mum of 8 mm.
• The right side of the moveable stop rails (16a) must be in
the inner positiion.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade (6) and
rotary table (14).
• Loosen the lock nut (27a) and adjust the adjustment screw
(27) until the angle between the saw blade (6) and the ro-
tary table (14) is precisely 45°.
• Re-tighten the lock nut (27a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (19) using a Philips screwdriv-
er, set to position 45° on the angle scale (18) and re-tighten
the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (fig.
1/2/11)
The crosscut, drag and mitre saw can be used to make mitre
cuts of 0° - 45° in relation to the work face.
Attention! For mitre cuts (inclined saw head), the
left side of
the moveable stop rails (16a) must be fixed in the outer posi-
tion.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
• The right side of the moveable stop rails (16a) must be in
the inner positiion.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) to the left, until the pointer (19) indi-
cates the desired angle measurement on the scale (18).
• Re-tighten the set screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45° (fig.
2/4/12)
The crosscut, drag and mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).