PWSAP 20-Li D4
■
108
│
DE
│
AT
│
CH
ACHTUNG!
♦
Dieses Ladegerät kann nur die folgenden
Batterien laden: PAP 20 A1/PAP 20 A2/
PAP 20 A3/PAP 20 B1/PAP 20 B3/
PAPS 204 A1/PAPS 208 A1.
♦
Eine aktuelle Liste der Akkukompatibilität
finden Sie unter www.Lidl.de/Akku.
Aufbewahrung und Handhabung
der empfohlenen Einsatzwerkzeuge
■
Schleifwerkzeuge sind mit Vorsicht zu be-
handeln und zu transportieren.
■
Schleifwerkzeuge sind so zu lagern, dass sie
keinen mechanischen Beschädigungen oder
Umwelt einflüssen (z. B. Feuchtigkeit) ausgesetzt
sind.
Arbeitshinweise
HINWEIS
►
Schleifkörper dürfen nur für die empfohlenen
Einsatzmöglichkeiten verwendet werden. An-
dernfalls könnten sie zerbrechen, beschädigt
werden und Verletzungen verursachen.
Schruppschleifen
Verwenden Sie niemals
Trennscheiben zum Schruppen!
■
Bewegen Sie den Winkelschleifer mit mäßigem
Druck über das Werkstück hin und her.
■
Führen Sie bei weichem Material die
Schruppscheibe in einem flachen Winkel über
das Werkstück, bei hartem Material in einem
etwas steileren Winkel.
Trennschleifen
Verwenden Sie niemals
Schruppscheiben zum Trennen!
■
Verwenden Sie nur geprüfte faserstoffver-
stärkte Trenn- oder Schleifscheiben,
die für
eine Umfangsgeschwindigkeit von nicht weniger
als 80 m/s zugelassen sind.
VORSICHT!
►
Das Schleifwerkzeug läuft nach dem Aus-
schalten nach. Bremsen Sie es nicht durch
seitliches Gegendrücken ab.
■
Sichern Sie das Werkstück.
Benutzen Sie
Spannvorrichtungen/Schraubstock, um das
Werkstück festzuhalten. Es ist damit sicherer
gehalten, als mit Ihrer Hand.
■
Schalten Sie das Gerät vor dem Ablegen
immer aus und warten Sie, bis das Gerät zum
Stillstand gekommen ist.
■
Verwenden Sie das Gerät nur für Trocken-
schnitt bzw. Trockenschliff.
■
Der Zusatz-Handgriff
8
muss bei allen Ar-
beiten mit dem Gerät montiert sein.
■
Asbesthaltiges Material darf nicht bearbeitet
werden.
Asbest gilt als krebserregend.
Tipp! So verhalten Sie sich richtig.
GEFAHR! FÜHREN SIE DAS GERÄT
IMMER IM GEGENLAUF DURCH DAS
WERKSTÜCK.
►
Bei entgegengesetzter Richtung besteht die
Gefahr eines Rückschlags. Das Gerät kann
aus dem Schnitt gedrückt werden.
■
Führen Sie das Gerät immer eingeschaltet
gegen das Werkstück.
Heben Sie das Gerät
nach der Bearbeitung vom Werkstück ab und
schalten Sie es erst dann aus.
■
Halten Sie das Gerät während der Arbeit
immer fest mit beiden Händen.
Sorgen Sie für
einen sicheren Stand.
■
Für die beste Schleifwirkung bewegen Sie
das Gerät gleichmäßig in einem Winkel von
15° bis 30° (zwischen Schleifscheibe und
Werkstück) auf dem Werkstück hin und her.
Summary of Contents for PWSAP 20-Li D4
