background image

PWSA 20-Li A1

■ 

10

 GB

CY

Working procedures

NOTE

 

Grinding tools should only be used for the 
recommended applications. Otherwise, they 
can break, be damaged or cause injuries.

Rough grinding:

 

  

Never use cutting discs for rough 
grinding!

 

Move the angle grinder with moderate pres-
sure back and forth over the workpiece.

 

For soft material, move the rough grinding 
disc at a shallow angle over the workpiece; 
for hard material at a slightly steeper angle.

Abrasive cutting:

 

  

Never use rough grinding discs for 
cutting!

 

Use only tested fibre-reinforced cutting or 
grinding discs

 that are approved for a circum-

ferential speed of not less than 80 m/s.

 

CAUTION!

The grinder continues running after being turned 
off. Do not try to brake it by applying lateral 
counterpressure.

 

Secure the workpiece! 

Use clamps/a vice to 

hold the workpiece firmly in place. This is much 
safer than simply holding it in your hand.

 

Always switch off the appliance before put-
ting it away and wait for the appliance to 
come to a complete standstill.

 

Use the appliance only for dry cutting or 
sanding.

 

The additional handle   must be mounted on 
the appliance for all work.

 

Materials containing asbestos may not be 
processed. 

Asbestos is a known carcinogen.

 

 

  

 

Tip! This symbol indicates proper  
behaviour.

 

 

HAZARD! ALWAYS GUIDE THE  
APPLIANCE THROUGH THE  
WORKPIECE IN REVERSE ROTATION.

 

In the opposite direction there is a risk of 
kickback. The appliance can be pushed out 
of the cut.

 

Always switch the appliance on before apply-
ing it to the workpiece. 

After completing the 

task, lift the appliance from the workpiece and 
then switch it off.

 

Always hold the appliance firmly with two  
hands while working.

Ensure that your stance  

is secure and stable.

 

For an optimum grinding effect, move the ap-
pliance evenly at an angle of 15° to 30° (be-
tween grinding disc and workpiece) backwards 
and forwards.

 

When working on angled surfaces, do not 
exert great force on the workpiece.

 If the 

rotational speed drops significantly, you must 
reduce the pressure exerted to allow safe and 
effective working. If the appliance suddenly 
brakes completely or jams, it must be switched 
off immediately.

 

Cutting: Work at a moderate feed rate and 
do not tilt the cutting disc.

 

Roughing and cutting discs become very 
hot – let them cool down completely before 
touching them.

 

Never use the appliance for purposes other 
than the ones for which it was designed.

 

Always make sure that the appliance is 
turned off before fitting the battery.

 

In the event of danger, turn off the appliance 
and remove the battery. 

Ensure that the ap-

pliance is easily and quickly accessible in the 
event of an emergency.

Summary of Contents for PWSA 20-Li A1

















































































Reviews: