background image

4

HOT GLUE GUN PHKP 500

Before you use it for the first time, it is essential that you make yourself fully familiar with the 
functions of the equipment and find out how to handle electrically powered tools. Please read the
following operating instructions       carefully along with the enclosed safety advice      . These 
instructions are to be considered as a constituent part of the product. 

FEATURES

Drip tray

Handle

Nozzle

Control indicator

 

Anti-skid support bracket

Mains connection charger

Discharge

Mains connection glue gun

Heating duct

TECHNICAL INFORMATION

1. Voltage:

240 V A/C

2. Frequency:

50 Hz

3. Nominal capacity:

30 W (500 W)

4. Insulating class:

II

5. Glue sticks:

11 mm

HOW TO USE

1. Insert the glue cartridge into the rear of the heating duct 

.

2. To heat the device we recommend connecting the power line with the charging station and 

inserting the plug into the outlet. Allow the hot glue gun to heat approx. 3 to 4 minutes – the 
control indicator 

 

on the handle 

will illuminate. Please ensure that the hot glue gun is 

positioned correctly, as shown in pic. 

so that any dripping glue is collected by the drip tray 

Optionally, the power line can also be connected directly to the hot glue gun.

3. Remove the gun from the charger after charging for a maximum 4 minutes. This allows working 

without cable for a short period of time.
Regulate the flow of the adhesive according to need by pressing the trigger 

accordingly.

4. Repeat the heating phase if the trigger is hard to depress, or if the adhesive exiting the gun 

is still thick.

5. Of course, if you prefer, you can work using the cable e.g. for gluing in batches.

Note:

To safely deposit the hot glue gun the support bracket must be attached to the front 

of the device.

Use the extra-long spare nozzle for points which are difficult to access. To change the nozzle 
just screw off/on.

WARNING:

Danger of burns. The nozzle heats up during operation. Change the nozzle only after 

switching the device off and allowing it to cool.

www.kompernass.com   +++   www.kompernass.com   +++  www.kompernass.com   +++    

Summary of Contents for KH 3119 HOT GLUE GUN









Reviews: