![background image](http://html1.mh-extra.com/html/parkside/kh-3050-electric-nailer/kh-3050-electric-nailer_manual_4178206006.webp)
7
GB/IE/CY
Introduction / General safety advice for electrical power tools
Technical data
Model: PET
25
Rated voltage:
230 V ~ 50 Hz
Firing speed:
30 / min
Short-term operation:
Max. 15 min
Protection class:
II /
Type 55
15 - 25 mm
Staple
width:
6
mm
Staple length: 15 - 25 mm
Type 47
15, 20, 25,
32 mm
Nail length:
15, 20, 25, 32 mm
Noise and vibration data:
Measured values for noise are determined in accord-
ance with EN 50144. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level:
83.1 dB(A)
Sound power level:
91.3 dB(A)
Uncertainty K:
2.5 dB
Wear hearing protection!
Vibration total values determined according to
EN 50144:
Vibration emission value a
h
= 5,615 m/s
2
,
Uncertainty K = 1.5 m/s
2
.
WARNING!
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified in
EN 50144 and can be used to compare devices.
Different uses of the device give rise to different
vibration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical pow-
er tool is used regularly in particular circumstances.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice
for electrical power tools
WARNING!
Read all the safety advice
and instructions!
Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUC-
TIONS IN A SAFE PLACE FOR FUTURE REFER-
ENCE!
THE TERM “ELECTRICAL TOOL” USED
IN THE SAFETY ADVICE REFERS TO ELECTRICAL
TOOLS POWERED BY MAINS ELECTRICITY (BY
MEANS OF A MAINS LEAD) AND ELECTRICAL
TOOLS POWERED BY RECHARGEABLE BATTER-
IES (WITHOUT A MAINS LEAD).
1.
Workplace safety
a)
Keep your working area clean and
well lit.
Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there
are inflammable liquids, gases or
dusts.
Electrical power tools create sparks,
which can ignite dusts or fumes.
c)
Keep children and other peo-
ple away while you are op-
erating the electrical tool.
Distractions can cause you to lose control of
the device.
Summary of Contents for KH 3050 ELECTRIC NAILER
