3
HALL EFFECT AND REED SWITCHES
Hall effect and reed switches can be specified to sense the
position of the tool plate by detecting the magnetic band on
the cylinder piston. Magnets are standard on all units.
Switches are mounted on the cylinder body and are easily
positioned. Order switches separately as well as the appro-
priate clamps shown in the table below. See specifications
for more detail.
Switching Logic:
Normally Open
Voltage Rating:
85-125 VAC or 5-30 VDC*
Power Rating:
10 Watts AC or DC/Resistive Load
5 Watts AC or DC/Inductive Load
Switching
Current Range:
10-200 mA/Resistive Load
(PC, Sequencer)
10-100 mA/Inductive Load (Relay)
Switching Response:
300 Hz Maximum
Breakdown Voltage:
1.8kVACrms for 1 sec., lead to case
Min. Current for LED:
18mA
Operating Temperature:
14° to 140° F(-10° to 60° C)
Lead Wire Length:
39 inches (1 meter)
AC125V
CR
R
C
=
=
(Recommended for longer
switch life 125V AC)
Put resistor and capacitor
parallel to loads.
CR: Relay coil (under 2W coil ratings)
R: Resistor under 1 K ohm
C: Capacitor 0.1 µF
(Required for proper operation
24V DC)
Put Diode parallel to loads
following polarity as shown below.
DC 12V
D
D: Diode: select a Diode with the breakdown
voltage and current rating according to the load.
CR: Relay coil (under 0.5W coil rating)
CR
INTEGRAL CIRCUIT FOR
SWITCHING CONTACT PROTECTION
-
+
-
+
(WHITE)
(WHITE)
BROWN**
(BLACK)
(BLACK)
BLUE**
BLUE**
BROWN**
* Polarity is restricted for DC operation
(+) to BROWN
(-) to BLUE
If these conections are reversed the contacts will close, but the LED will not light.
Prior to October, 1993:
(+) WHITE
( - ) BLACK
** Applies to Switches Manufactured
After 10/15/93.
4 Black
Not Used
1 Brown
3 Blue
Quick
Connect
Option
Hall Effect Switch Part No.
1467150000 (PNP)
1467140000(NPN)
146715000C (NPN Quick Connect)
146714000C (NPN Quick Connect)
Reed Switch Part No.
1459030000- Standard
145903000C-Quick Connect
(RED)
SWITCH
_
+
LOAD
* When connecting Inductive
Load (relay, electromagnetic
valve etc.) it is recommended
to insert protection circuit.
Diode 100V 1A. (NPN
connection shown)
Type:
Solid State Type (PNP or NPN)
Switching Logic:
Normally Open
Supply Voltage Range:
5 - 30VDC
Current Output Range:
Up to100 mA at 5 VDC,
Up to 200 mA at 12 VDC and 24 VDC
Current Consumption:
7 mA at 5 VDC, 15 mA at 12 VDC,
and 30 mA at 24 VDC
Switching Response:
1000 Hz Maximum
Residual Voltage:
1.5V Maximum
Leakage Current:
10uA Maximum
Breakdown Voltage:
1.8kVACrms for 1 sec., lead to case
Min. Current for LED:
1mA
Operating Temperature:
14° to 140° F (-10° to 60° C)
Lead Wire Length:
39 inches (1meter)
BROWN**
(BLACK)
(WHITE)
BLUE**
SWITCH
LOAD
SWITCH
LOAD
BROWN**
(RED)
(WHITE)
BLACK**
BLUE**
(BLACK)
BROWN**
(RED)
BLACK**
(WHITE)
(BLACK)
NPN WIRING CONNECTION
BLUE**
** Applies to Switches Manufactured
After 10/15/93.
DC 5 - 30V
DC 5 - 30V
Quick Connect
Option
1 Brown
3 Blue
4 Black
Model
Clamp Part Number
04
L074730056
06
L074730075
08
L074730106
12
L074730150
PNP WIRING CONNECTION
6" Lead
3 BLUE
1 BROWN
Quick Connect
Option
4 BLACK
REED SWITCH SPECIFICATIONS
HALL EFFECT SPECIFICATIONS
BLACK**
+
_
_
+
