Parker PSD1 Installation Instructions Manual Download Page 28

Page: 28 / 109

Installation of the individual drive PSD1-S

28 (109)

192-011006N8 2019-07

09.10.19 09:27

4.2

Mounting and dimensions

Ventilation:

•

During operation, the device radiates heat (heat dissipation). Please provide for

a sufficient mounting distance below and above the device (at least 100 mm) in

order to ensure free circulation of the cooling air.

•

Please do also respect the recommended distances of other devices.

•

Make sure that the mounting plate is not exhibited to other temperature

influences than that of the devices mounted on this very plate.

•

The devices must be mounted vertically on a level surface. Make sure that all

devices are sufficiently fixed.

4.2.1.

Mounting and dimensions PSD1-S

Mounting:

2 socket head screws M6

Lateral distance of fixing of mounting holes: 50.5 mm

Required mounting distance for heat regulation at the top and below: At least

100mm

Please check regularly the firmness of the screw connection!

Summary of Contents for PSD1














































































































Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands

Parker PSD1, Installation Instructions Manual

Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands