background image

12

13

ASSEMBLY

Parts needed

: 1 x foot + 1 x M8 lock nut.

Raise or tilt pressure washer so you can line up foot 

with the hole located at the centre of the frame.

Align the rubber foot with the hole in the frame where 

the foot is to be located. Attach foot by inserting the bolt 

from the bottom up and install the acorn nut. 

Wrench tighten until there is a slight crush on the frame 

tube - do not over tighten.

Install the upper frame (handle) onto the lower frame 

by sliding the handle over the two upright tubes on 

the lower frame and pressing down firmly until the 

handle is seated, and the two pins snap in place.

1

ATTACH FOOT ASSEMBLY

2

INSTALL HANDLE

3

ASSEMBLY

Attach the accessory hook.

Install two plastic rivets until the plastic rivet is snug.

Note: You may need to tap with a mallet or small ham-

mer to seat the lock pin.

Screw the spray wand and the trigger handle together 

until they are secure.

Insert the inlet coupler of the spray hose into the 

threaded fitting on the high pressure spray gun and 

thread the black nut on by turning clockwise until it is 

hand tight.

4

ATTACH ACCESSORY HOOK

ATTACH SPRAY GUN

4

ATTACH THE HOSE

A

B

Be careful not to crossthread the fitting as the threads are extremely fine. Take extra care throughout 

this step. 

Summary of Contents for PPPW-3100





















Reviews: