manualshive.com logo in svg

PARK AUDIO DF DSP Series, Owner'S Manual

Share
Download
PARK AUDIO DF DSP Series Owner'S Manual Download Page 5

3

DESIGN FEATURES

Physical Design

The amplifier is enclosed in a metal (steel) case of 88 mm (2U) height. The amplifier 

is designed to be standard  rack-mounted   (RACK 19").

Power Supply Unit

All four channel of the amplifier share the same pulse power supply unit.

Power Factor Correction (in DF2008

DSP

 only) 

The amplifier has power supply with Power Factor Correction, which significantly 

reduces load to the mains and also reduces noise and distortion in   the mains. What is 
more important, the amplifier output power is no longer rigorously dependent on the mains  
voltage.

The amplifier provides full power at the mains voltage from 160 V to 250 V (with no 

need to use of external AC voltage stabilizer).

Cooling System

The amplifier features a forced cooling system which is common for all four channels. 

The amplifier and the power supply unit are cooled with a single fan blowing front to rear. 
The cooling system provides for a double-step intensity-cooling rate switching. At a normal 
temperature, the fan runs at a low speed, thus generating the least noise possible. When 
the amplifier is set to deliver a high output power or when the ambient temperature is 
higher than normal, the cooling system may switch the fan to the other (higher) cooling 
rate.

Output Stage

The output stage of this digital power amplifier is designed according to Class D 

technology to deliver high efficiency and least heat. The high switching rate ensures the 
high sound quality comparable with the best analogue amplifiers.

Balanced Inputs

The use of balanced inputs provides for an essential reduction of the environment-

induced hum and noise interference with long input connecting cables.

Line Outputs

The  amplifier  line  outputs  are  parallel  to  the  inputs  (each  along  the  respective 

channel) and provide for parallel connection of several amplifiers with standard signal 
cables using  

XLR

 connectors. 

If necessary, the signal, processed by the 

DSP

, can be applied to the line outputs. 

This  mode  is  set  at  the  factory  or  by  the  customer  (manufacturer  get  corresponding 
instructions by e-mail: [email protected]).

DSP 

Built-in 

DSP

 accurately handles the audio signal due  to its functions of equalization, 

filtering, delay and limiter. Processor has 2 inputs and 4 outputs and provides free signal 
routing from any input to any output.

 

DSP

  enables  users  to  choose  between  eight  factory  preset  settings.  Preset 

parameters are listed on the insert in the 

Owner’s Manual

. 

Any  of  presets  can  be  modified,  using  a  computer  connected  via  USB  interface 

(software – 

SigmaStudio

 by 

Analog Devices

, 

Inc

.).  

Summary of Contents for DF DSP Series



























Reviews:

No comments

Brands by name

Popular brands

Load more brands