Parasound Halo T 3 Owner'S Manual Download Page 15

OPERATING YOUR T 3

Remote Control and Front Panel Operation

Front panel and remote control operation of the T 3 are very similar. However, the 
remote control handset gives you control of the following functions not available on the
front panel:

Discrete On
Discrete Off
Discrete Preset Station Access
Direct Frequency Entry
Choice of Seek (auto tuning), Tune (manual tuning), or Preset (preset selection)
RDS (Radio Data System) Activation

For your convenience, it also enables remote control of the companion Parasound P 3 
Preamplifier. The preamplifier buttons are a different color for easy identification.

The remote uses two standard AAA batteries that are included. Make sure you insert the
batteries in the direction indicated on the molded battery compartment. When the 
batteries wear out, please recycle them and replace them only with alkaline batteries. 

Turning the T 3 On and Off 

You can turn the T 3 on and off with the 

On-Off

button on its front panel, with the 

On

and

Off

buttons on its remote control handset, or with an external DC source. 

Turning the T 3 On

Press the 

On-Off

button on the front panel, the 

On

button on the remote control, or apply

an external DC voltage.

Turning the T 3 Off

Press the 

On-Off

button on the front panel, the 

Off

button on the remote control, or 

remove the external DC voltage.

YOU SHOULD KNOW

When the T 3 is turned off, there is a faint glow behind its On-Off button and its P logo badge to
indicate that AC power is present. When you turn on the T 3, the P badge and the glow behind
the On-Off button brightens, and the front panel display lights up to show the last selected
station. 

Selecting Radio Stations on the T 3

FM-AM Bands

The 

FM-AM

button on the front panel and remote control switches between FM or AM 

bands. Each time you press the FM-AM button it changes from the FM band to the AM 
band or vice versa.

YOU SHOULD KNOW

The T 3 remembers if you were listening to an FM or AM station before you last turned it off.
You don’t need to press the FM-AM button if you want to continue listening to the same band.

12

See

page 18 for T 3 Front Panel and Remote Control layout

Summary of Contents for Halo T 3




























Reviews: