Parasound HALO JC 1 Owner'S Manual Download Page 13 | Manualshive

Page: 13 / 22

background image

MAINTAINING YOUR PARASOUND JC 1

10

Notes:

Your Parasound JC 1 power amplifier requires no periodic maintenance and has no user-

serviceable parts inside. To avoid the risk of electric shock, do not remove its top cover. The

amplifier’s exterior can easily be cleaned with a soft cloth pre-moistened only with a few drops

of water or glass cleaner.

Main Power Fuse

If this fuse blows, please contact Parasound Technical Service for further advice.

«
...
11
12
13
14
15
...
»

Summary of Contents for HALO JC 1























Reviews:

No comments

Related manuals for HALO JC 1

Brand: QUAD Pages: 7

Brand: Cable Electronics Pages: 2

Brand: NAD Pages: 18

Brand: NAD Pages: 2

Brand: James Loudspeaker Pages: 12

Brand: DAD Pages: 24

Brand: Halcro Pages: 55

Brand: Ramsey Electronics Pages: 20

ProX 840.4 COMP

Brand: µ-Dimension Pages: 7

Brand: µ-Dimension Pages: 7

Brand: µ-Dimension Pages: 6

Brand: µ-Dimension Pages: 3

mDB-2500.1D Comp

Brand: µ-Dimension Pages: 11

Brand: Arcam Pages: 18

Brand: KODA Pages: 35

Brand: Akai Pages: 22

IronHorse DH40H

Brand: Traynor Pages: 18

Brand: AMERITRON Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands