background image

Paragon Classic Floss 5” Cotton Candy Machine 

Included Parts 

 

Machine Base

 

 

Aluminum Bowl 

 

 

Bubble Top

 

 

Mesh Bowl Netting

 

 

(8) Mesh Net Clips

 

Operating Instructions 

Be sure equipment is connected to properly grounded 120 volt power supply with 15 amp circuit. 

Operation

 

1.

 

Loosens the two shipping travel knobs. (These are the knurled knobs on either side of the motor 
cover, below the head.) 

2.

 

Place aluminum bowl on top of base. Bowl just rests on top of base, does not need to be 
secured.  

3.

 

Line inside of the bowl with mesh net. Secure with provided clips.  

4.

 

Press the MOTOR switch to the “ON” position.  

5.

 

Fill the spinner head with the desired amount of sugar floss. Never fill the head past the bottom 
level of the filler spout.  

6.

 

Place bubble top on top of aluminum bowl.  

7.

 

Press the HEAT switch to the “ON” position.  

8.

 

Turn the HEAT CONTROL knob to setting HIGH.  

9.

 

Once floss starts to flow out of the head, reduce the HEAT CONTROL accordingly. (Note: Too 
high of a setting will cause cutting of the floss and potentially clog the screen assembly.) 

10.

 

When the amount of floss that is being produced starts to slow, add more sugar. DO NOT adjust 
the HEAT CONTROL knob setting. 

 

Shutting Down 

1.

 

Press the HEAT switch to the “OFF” position.  

2.

 

Wait 3-5 minutes for the spinner head to cool down. 

3.

 

Press the MOTOR switch to the “OFF” position. 

4.

 

For end of day procedures, operate the machine until the remaining sugar floss in the head is 
gone, then do steps 1-3. 

5.

 

 IF THE MACHINE IS TO BE MOVED: Retighten the two shipping travel knobs to prevent damage 
to the head during transit.  

 

(Note: Some smoking may appear as the head is run out of sugar. This is normal and will clean any 
residual sugar from the screen.) 
 

In case of malfunction immediately shut-off the MOTOR and HEAT switches and correct the 
problem. 
 

Summary of Contents for Classic Floss 5

Page 1: ... the ON position 8 Turn the HEAT CONTROL knob to setting HIGH 9 Once floss starts to flow out of the head reduce the HEAT CONTROL accordingly Note Too high of a setting will cause cutting of the floss and potentially clog the screen assembly 10 When the amount of floss that is being produced starts to slow add more sugar DO NOT adjust the HEAT CONTROL knob setting Shutting Down 1 Press the HEAT sw...

Page 2: ...ining nuts and leather floaters on the top of the SPINNING HEAD unit 4 Remove the top from the SPINNING HEAD unit by lifting it off 5 Remove the slinger plate by losing the two nylon acorn nuts in the center 6 Disconnect the two heater lead terminations by removing the two nuts 3 8 hex and removing the leads from the studs 7 Remove the outer screen assembly with the heating element by sliding it s...

Page 3: ...ne up with the ring of floss attached and rotate the cone to wrap the floss DO NOT roll floss while the cone is inside the pan This will pack the floss too tightly 4 If the floss fails to stick to the cone pass the cone near the spinner head to pick up a starter of melted sugar Lift the cone out of the pan and wrap the floss with a figure eight movement of the hand This leaves giant pockets and ma...

Page 4: ... low on the netting twist the front leading edge of the leather floaters down You get more lift and the floss will collect higher For video demonstration on how to make floss go to https www youtube com watch v G25raDlY0D0 It s not the same model of cotton candy machine but the general idea is there ...

Reviews: