background image

 18

Declaration of Conformity

This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2
and 15 of the Federal Communications Commission’s Rules. This compliance
information statement pertains to the following products:

Trade Name:

Hotwire

Model Number:

5620-A2-200

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that may
cause undesired operation.

The name, address, and telephone number of the responsible party is given below:

Paradyne Corporation
8545 126th Avenue North
Largo, FL 33773-1502
Phone: (727) 530-2000

The authority to operate this equipment is conditioned by the requirement that no
modifications will be made to the equipment unless the changes or modifications are
expressly approved by Paradyne Corporation.

In order to maintain compliance with Part 15, FCC rules, the clamp-on ferrite chokes
must be installed on the Ethernet cable and the Power cable in accordance with the
installation instructions.

Summary of Contents for Hotwire 5620 RTU





















Reviews: