Paradyne FrameSaver 9120 User Manual Download Page 58

Page: 58 / 82

Maintenance and Troubleshooting

5-2

9121-A2-GB20-20

May 1998

FrameSaver 9120 Access Unit

Label

Indication

Color

What It Means

Power and
Operational
Status

Green

ON –

Access unit has power and is
operational.

OFF –

Access unit is in a power-up self-test,
or there is a failure.

Blinking ON and OFF ( Rate: 1 Hz ) –

Software is being downloaded.

ALM

Operational
Alarm ( Fail )

Red

ON –

Access unit has just been reset, or an
error or fault has been detected.

Error/fault/alarm conditions:

Out of Frame ( OOF )

Loss of Signal (LOS)

Alarm Indication Signal (AIS)

Exceeded Error Rate (EER)

Yellow Alarm Signal

Device Fail

DBM Card Failed

Memory Failed

T1 Failed

CPU Failed

ISDN Network Failed

LMI Down

DLCI Down

Network Communication Link Down

CTS Down to device

DTR Down to device

Download Failed

Primary or Secondary Clock Failed

OFF –

No failures have been detected.

When an ISDN BRI DBM is installed, if the OK LED comes on during power recycling,
then goes off, the ISDN BRI DBM has probably failed.

Summary of Contents for FrameSaver 9120


















































































Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands

Paradyne FrameSaver 9120, User Manual

Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands