Paradyne FrameSaver 9120 User Manual Download Page 31

Page: 31 / 82

Displaying System Information

4-5

9121-A2-GB20-20

May 1998

Health and Status Messages:

These messages appear in the left column of the System and Test Status screen,
or the highest priority Health and Status message appears on the last line at the
bottom of the screen (right corner).

Message

What It Indicates

What To Do

AIS at Network

An Alarm Indication Signal
(AIS) is received by the
network interface. AIS is an
unframed, all ones signal.

1. Upstream access unit is

transmitting AIS
(keep-alive signal).

2. The network is

transmitting an AIS.

1. Check status of upstream

access unit(s).

2. Report problem to carrier.

AIS at DSX-1

An Alarm Indication Signal
(AIS) is received by the
DSX-1 interface. AIS is an
unframed, all ones signal.

Check the DTE attached to the
DSX-1 interface.

Backup Active

Backup has been
established and data is
flowing over the alternate
DLCI.

No action needed.

BRI-B

n Call Profile

Disabled

ISDN backup call (manual
or automatic) could not be
made because the Call
Profile had been disabled.

Enable the ISDN Call Profile
(

Main Menu

→

Control

→

ISDN Call Profiles

→

Enable)

BRI-B

n Call Profile

Invalid

ISDN backup call (manual
or automatic) could not be
made because the Call
Profile is invalid.

1. Verify that the ISDN Call

Profile identifier is not blank.

2. Check that the phone number

associated with the ISDN Call
Profile is valid.

Configuration Shortcut
Active

Configuration Shortcuts
feature is active, which
allows automatic
configuration and
cross-connection of DLCIs
as they are activated by the
network.

No action needed unless you
want to disable this feature,
selected from the Main Menu.

CTS down to Port-

Device

The Port

n CTS control

lead on the access unit is
off.

1. Verify that the port is enabled.

2. Check DTR from Port-1 or

Port-2.

DBM Download
Required

A download attempt was
interrupted and failed to
complete.

There are incompatibilities
between the NAM and
DBM software.

Only appears when a dial
backup module (DBM) is
installed.

Download function is controlled
and for service personnel only.

Call your service
representative.

Summary of Contents for FrameSaver 9120


















































































Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands

Paradyne FrameSaver 9120, User Manual

Search results

Summary of Contents for FrameSaver 9120

Reviews:

Related manuals for FrameSaver 9120

Brands by name

Popular brands