background image

12

EMI Notices

United States – EMI Notice:

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no 
modifications will be made to the equipment unless the changes or modifications are 
expressly approved by Paradyne Corporation.

If the equipment includes a ferrite choke or chokes, they must be installed per the 
installation instructions.

Canada – EMI Notice:

This Class A digital apparatus meets all requirements of the Canadian 
interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du réglement sur 
le matérial brouilleur du Canada.

Summary of Contents for ENE2000-P

















Reviews: