background image

1

ENE2000-P and ENE2000-S

E1 Network Extenders Installation Instructions

Document Number ENE2-A2-GN12-10

September 2005

Contents

Software and Firmware License Agreement

.................................................

1

Product Documentation

................................................................................

3

Warranty, Sales, Service, and Training Information

......................................

3

Package Contents

.........................................................................................

3

Powering Up the ENE2000

...........................................................................

4

Configuring the E1 Port

................................................................................

5

Connecting the E1 Line

................................................................................

8

Connecting the Ethernet Line

.......................................................................

8

LED Indicators

..............................................................................................

9

RJ45 Pin Assignments

.................................................................................. 11

EMI Notices

.................................................................................................. 12

Important Safety Instructions

........................................................................ 13

Software and Firmware License Agreement 

The terms and conditions of this License Agreement (the “Agreement”) will apply to the 
software and/or firmware (individually or collectively the “Software”) incorporated into 
the Paradyne product (the “Product”) purchased by you and any derivatives obtained 

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.

Summary of Contents for ENE2000-P

















Reviews: