Paradyne 9121 User Manual Download Page 41

Page: 41 / 73

Displaying System Information

4-17

9121-A2-GB20-00

June 1997

Field

What It Indicates

Status

Active Call Profile

8-Character ISDN Call
Profile identifier

ISDN Call Profile used for this
B channel.

Appears when a call is active or in
progress.

Last Cause Value

Various ITU cause
messages

Refer to the

Last Cause Value

Messages

section in Chapter 5,

Maintenance and Troubleshooting.

Remote Call ID

None

Backup has never been active on
the B channel.

Remote device’s ID

Remote call origination – Calling ID
of the remote device.

Local call origination – Called ID of
the remote device.

Negotiated Rate

64 Kbps
56 Kbps

Negotiated rate of the connection/
link.

Performance Statistics

Use the Status menu to display statistical information for a selected interface:

Network, Port-1, Port-2, DBM / BRI-B1, or DBM/BRI-B2. Statistical information is

useful when trying to determine the severity and frequency or duration of a
condition.

NOTE:

All statistics show the number of occurrences since the last reset of the
counter. In addition, only Level-1 and Level-2 Access Levels can view the
statistical information collected.

What Statistics Are Collected?

Performance statistics are collected for the:

Physical interfaces

Frame relay link

Frame relay DLCI PVC connections

Summary of Contents for 9121









































































Search results

Summary of Contents for 9121

Reviews:

Paradyne 9121, User Manual, Page: 41 / 73

Search results

Summary of Contents for 9121

Reviews: