manualshive.com logo in svg

Paradyne 9109, Installation Instructions Manual, Page: 6 / 8

Share
Download
Paradyne 9109 Installation Instructions Manual Download Page 6

 6

Installing the APM

The APM can be installed in any slot 

except Slot 01.

CAUTION:

You must insert the Synchronous Data APM in the correct slot so that it
mates with its matching I/O card. APMs are keyed so that they mate only with
their matching I/O cards.

1. Remove the filler panel, if applicable. See the installation instructions that came

with your housing for information.

2. Remove the APM from the shipping box. Handle only by the top and bottom edges

to avoid damaging the card.

3. At the front of the housing, align the APM with the upper and lower tracks of the

selected slot.

98-15152-02

Ejector

Latches

Ejector

Latches

5-Slot

2-Slot

Front View

4. Slide the APM into the tracks until it seats with the midplane connectors. Be careful

not to force the card or bend any pins.

5. Close both the upper and lower ejector latches on the housing to lock in place, then

tighten the captive screws.

Reinstalling the Bezel

1. Insert the bezel into the two slots at the bottom of the front of the housing.

2. Snap the bezel in place using the latch at the top.

Summary of Contents for 9109









Reviews:

No comments