Paradyne 6310 MVLT Installation Instructions Manual Download Page 10

98-15304a

6-Pin

RJ11 Plugs

Pin #1

Pin #6

 10

To enable the sharing of resources and review security considerations, see Microsoft’s
Web site at www.microsoft.com.

In this example of HomeLink, the PC in the family room could use the office printer.

98-15952a-01

RJ11

Wall

Jack

MVL Modem

Office

PHONE

POWER

ETHERNET

LINE

Hub

FAX

Ethernet

Cable

Printer

RJ11
Wall
Jack

PHONE

POWER

ETHERNET

LINE

MVL Modem

Family Room

Increasing the Number of End-User Systems

A single end-user system is attached to the Hotwire 6310 MVL Modem by using an
Ethernet crossover cable. To increase the number of end-user systems, connect all the
PCs to an Ethernet hub using a straight-through cable.

On one line, the MVL system provides the capability to use up to four 6310 MVL
modems and 32 end-user systems in any combination.

Cables & Connectors

This section is reference information.

Standard twisted-pair CAT3 or better cables are recommended.

H

The LINE and PHONE interface connectors use 6-pin, non-keyed modular plugs.

RJ11 6-Pin Connector

Pin #

Function

1 & 2

Not used

3

MVL Ring

4

MVL Tip

5 & 6

Not used

Summary of Contents for 6310 MVLT





















Reviews: