Paradyne 5011 Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 23

background image

12

5020-A2-GN10-60

April 2000

Installing the POTS Splitter Card into the Chassis

!

HANDLING PRECAUTIONS FOR
STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal operation.
When performing installation procedures, however, take proper static
control precautions to prevent damage to equipment. If you are not
sure of the proper static control precautions, contact your nearest
sales or service representative.

Procedure

To install a POTS splitter card into the POTS splitter chassis:

1. Remove the slot filler panel, if necessary, by loosening the 1/4-turn fastener

on either side.

2. Slide the POTS splitter card into the chassis.

3. Tighten the 1/4-turn fastener on each side of the faceplate of the POTS

splitter card.

TM

DSL Interface

Loop Interface

PSTN Interface

99-15431-01

CO POTS Splitter
6-Slot Chassis

1/4-Turn

Fastener

1/4-Turn

Fastener

Filler

Panel

496-15104

«
...
10
11
12
13
14
...
»

Summary of Contents for 5011
























Reviews:

No comments

Related manuals for 5011

Brand: DigitalZone Pages: 30

CABLINE-UY 20857-0 T-0 Series

Brand: I-PEX Pages: 7

Brand: Tripp Lite Pages: 2

Brand: ACME Pages: 4

Brand: W&T Pages: 12

Brand: Pro-face Pages: 8

EYP A A00Q01 Series

Brand: Lenze Pages: 6

Brand: Labgear Pages: 4

Brand: Meltric Pages: 2

Brand: Meltric Pages: 2

Brand: S-Impuls Handels Pages: 2

Brand: MuxLab Pages: 2

Brand: MAC Panel Pages: 2

Raychem IEK-25-PIPE

Brand: nvent Pages: 16

Brand: HSS Hire Pages: 2

Brand: Walther-Werke Pages: 18

Brand: Xo Pages: 2

Brand: THG Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands