Paradyne 3980-A2-GZ40-20 Page 9 Features Manual Download

Page: 9 / 18

3980-A2-GZ40-20

November 1996

Table 3

AT Commands for SDC

Command

Description

DCP LCD

Command

Sequence

#DM

SDC Delay Minimization.

Minimizes the delay introduced by SDC by allowing the modem to transmit a
DTE frame to its DTE in a discontinuous way.

#DM0

No delay minimization. The modem does not begin transmitting a
frame to its DTE until the entire frame has been received.

#DM1

Delay minimization. The modem begins to transmit data from a
DTE frame to its DTE even if the end of the DTE frame has not yet
been received by the modem.

The factory setting is No Delay Minimization.

Configure\Edit\
V42/MNP/Buffer

Sync Flow Ctrl. Synchronous Flow Control of DTE.

Controls the type of synchronous data flow control while using data
compression.

#Q0

No flow control.

#Q1

Flow control using transmit clock (circuit 114).

#Q2

Flow control using CTS (circuit 106).

The factory setting is No Flow Control.

Configure\Edit\
V42/MNP/Buffer

#SC

Sync Comp Mode. Synchronous Compression Mode.

Enables and disables synchronous data compression.

#SC0

Disable Synchronous Data Compression mode.

#SC1

Enable Synchronous Data Compression mode.

The factory setting is Disable.

Configure\Edit\
V42/MNP/Buffer

Summary of Contents for 3980-A2-GZ40-20



















Search results

Summary of Contents for 3980-A2-GZ40-20

Reviews:

Related manuals for 3980-A2-GZ40-20

Brands by name

Popular brands

Paradyne 3980-A2-GZ40-20, Features Manual

Search results

Summary of Contents for 3980-A2-GZ40-20

Reviews:

Related manuals for 3980-A2-GZ40-20

Brands by name

Popular brands