12Vdc
Battery
+
-
TM
Door 2
Door 1
1
2
3
4
REX Devices
Contact
1 kΩ**
Optional
external trigger
Fail secure
latch (N.O.)
*
+
-
16 - 36Vdc
Power supply
~
~
16 - 24Vac
Power supply
or
PS27D Power supply
Internal Power
Supply
Jumper
To COM of relays
COM
G R1 T1 RG TP
C 1 2 3 4 C 5 6 7 8
2-WIRE
SMOKE
C
1 2 3 4 COM NC NO
BELL
A+ B-
RED
GRN
BLK
YEL
BATTERY TBL
ETHERNET
10/100 Mbps
BATTERY
USB POWER
16 / 24 Vac
ETHERNET
PHONE LINE
MULTIBUS
RS485 ACCESS
ZONES
13.8 Vdc AUX
700 mA MAX.
PGM 5
5A
PGM
100mA
V32
USB 2.0
PORT
USB RX/TX
RS485 RX/TX
BELL
Input Power
Use a 16-24V
AC
(50/60 Hz)
transformer with minimum
75VA. as shown in the
connection diagram. Do not
use switch-controlled outlets
to power the transformer. It
is possible for modules to
share a central
AC
supply
(16 to 24 V
AC
)
throughout
the system.
Backup Battery
To power the module’s door lock relay during a power failure, connect a
12Vdc (minimum capacity of 7Ah) rechargeable acid/lead or gel cell
backup battery as shown in the connection diagram. Apply AC power
before connecting the battery.
Use supplied cable. If using custom wiring, add a fuse near the battery.
Battery charge current: 350mA/500mA (configurable in BabyWare).
Jumper Settings (J2)
When the J2 jumper is ON, internal
power is fed to
COM
of both relays (up
to 2A at 12V). If using external power,
remove the J2 jumper and supply
power to the
COM
input (see below).
Remove J2 jumper before
supplying external power.
Readers
Each ACM24D on a V32 can be assigned with up to 4 readers / 2
per door (EVO/DGP - 2 readers / 1 per door). The ACM24D
supports R910 (V2.0 or higher) and/or R915 (any version) 4-wire
card readers (up to 500mA). Readers 3 and 4 are optional and
can be used as passback or SAS readers (one man trap, two-door
access).
Readers are assigned to the ACM24D in BabyWare (Imperial) or
WinLoad/keypad assignment (EVO/DGP).
Reader LED
Orange slow flash = reader start up / too many readers on module
Orange fast flash = reader not assigned
Red on = reader is assigned to a door
* 1N4007 Diode
Connect the cathode to + voltage
Connect anode to - voltage
Do not use a diode with AC power
** Follows control panels EOL definition
Anode
Cathode
Connecting an External Trigger
The external negative trigger can also be activated using a
push button. When the push button is pressed, the door will
unlock. The PGM or push button must ground the negative
trigger.
Energy Saving Feature
When door locks are activated, voltage increases*. When
the activation period expires*, the ACM24D will go into
power saving mode and voltage will be reduced*.
This feature is only available when using internal power (J2
on).
* These settings are configurable with BabyWare software.
External Power
Technical Specifications
Power Input Voltage:
16-24Vac / 16-36Vdc
Transformer Sharing compatible
Power Input Rating:
75VA / 50W
Current Consumption:
min. 127mA max. 183mA
Aux. Readers:
12Vdc, 500mA max.
Aux. Locks:
6-12Vdc, 3.1A (internal)
Battery:
12Vdc, 7Ah
No. of Outputs:
2 x form C relay rated at 3.5A per door / 28Vdc,
N.O. / N.C.
No. of Zones:
4 (Door Contact & REX device - 2 per door)
No. of Inputs:
2 (Negative Trigger - 1 per door)
Operating
temperature:
0ºC to 50ºC (32ºF to 122ºF)
Software:
BabyWare, WinLoad V4.6
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found
on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all
warranty terms and conditions.
Paradox Imperial, Mama, Paradox Mama and BabyWare are trademarks or registered trademarks of
Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries. Mark
X is a registered trademark of Koninklijke Philips Electronics N.V For the latest information on products
approvals, such as UL and CE, please visit www.paradox.com.
© 2008 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice.
One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259,
5886632, 5721542, 5287111, 5119069, 5077549 and RE39406 and other pending patents may apply.
Canadian and international patents may also apply.
~
~
24Vac
Power supply
J2 OFF =
External
power
J2
24Vac
Latch
*
*
24Vac
Latch
V32 control panel
(RS485 ACCESS)
Power Supply
The V32’s RS485 bus must
be supplied with 12Vdc
power.
