ParaBody GS6 User Manual Download | Manualshive

Page: 30 / 33

background image

30

FIGURE 32

AT

39

AM

ADJUSTMENT

• If upon completion of assembly, the HEAD PLATE (AK) does not sit on top of the first WEIGHT PLATE, push the HEAD PLATE (AK)

down, insert the WEIGHT SELECTOR PIN and perform several repetitions at the press station.This will relax the cable system and
prevent the HEAD PLATE (AK) from lifting up. See FIGURE 32.

• If after completing previous step, the HEAD PLATE (AK) still does not sit on top of the first WEIGHT PLATE or if there is excess slack

in the cable system, adjust the threaded end of the LAT CABLE (AV) and FLOATING PULLEY BRACKET (W) accordingly and
retighten the jam nuts. See figure 32.

• For maximum performance, the HEAD PLATE (AK should just barely sit on the top WEIGHT PLATE

• Attach the LOW ROW BAR (AM) to the ball end of LAT CABLE (AV) using one SNAP LINK (39) as shown in FIGURE 32.

• Attach the ANKLE STRAP (AU) to the 12 LINK CHAIN (38) using one SNAP LINK (39) as shown in FIGURE 32

Thank you for purchasing the ParaBody GS6 Gym System. If unsure of proper use of equipment, call
your local ParaBody distributor or call the ParaBody customer service department at (800) 328-9714

STEP 32:

38

ADJUSTMENT

• Attach the AB STRAP (AT) to the ball end of LOW CABLE (AW) using one SNAP LINK (39) as shown in FIGURE 32.

AU

39

TIGHTEN
JAM NUT
SECURELY

AK

A

W

AY

«
...
28
29
30
31
32
...
»

Summary of Contents for GS6


































Reviews:

No comments

Related manuals for GS6

Brand: ParaBody Pages: 3

Brand: Vectra Fitness Pages: 8

LIFT Multi Functional Folding Weights Bench

Brand: BLUEFIN Fitness Pages: 134

Brand: NordicTrack Pages: 33

Brand: Body Solid Pages: 32

Brand: Adidas Pages: 17

Brand: Adidas Performance Pages: 28

Brand: ParaBody Pages: 18

Brand: Universal Pages: 2

NordicTrack RW200

Brand: ICON Health & Fitness Pages: 24

Brand: Body Solid Pages: 15

Brand: MBH Fitness Pages: 12

Brand: Thane Fitness Pages: 20

Compact Home Gym

Brand: V-fit Pages: 28

Power Tower 8532PT

Brand: Pure Fitness Pages: 12

Brand: OPTi Pages: 18

Brand: Marcy Pages: 12

Brand: Marcy Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands