background image

As can be seen from the table, for example, Panduit can only supply up to 25.5 W at 1,263 feet with 23 AWG cable.

5

Using External Power Supply at Transmitter Only 

This section looks at the scenario where only a 60 W external power supply (such as the POWER-60W power supply) is 

connected to the transmitter. No other power is provided to the receiver.

Note: it is possible to provide power to the receiver through another separate power supply. This can be done in cases where 

additional power is needed at the receiver in order to power the end device. Powering the receiver will not provide power to 

the transmitter. See the “Using External Power Supply at Receiver Only” section for more information on this use case.

Table 3 provides guidance as to the maximum distance between the transmitter and receiver when only the transmitter is 

powered by a 60 W external power supply.

 

 The “Max Wattage at PD” refers to how much power is available at the Powered Device (PD)

 

 The amount of power needed is dependent on the requirements of the Powered Device (such as 

 

  a security camera)

 

 The “TX1 – RX1 Cable Distance ft. (m)” refers to how far the transmitter and receiver can be 

 

  separated from each other with either 23 AWG cable or 24 AWG cable

 

 Panduit recommends 23 AWG cable as it provides further distance

 

 In all cases, we recommend no more than 50 feet (15 meters) from the transmitter and receiver 

 

  and the corresponding devices they are connected to

 

 In the case where a 4-port receiver (POEXRX4) is connected to the transmitter, the “Max Wattage 

 

  at PD” must be split amongst the four ports, offering a lower total power available per port

PoE Class

Standard

Max Wattage 

at PD

Under Voltage 

Lockout at PD

PSE – TX1

TX1 – RX1 Cable Distance ft. (m)

RX1 – PD

23 AWG 

(1.04Ω/100 ft.)

24 AWG 

(1.43Ω/100 ft.)

1

802.3af

3.84

37

50 ft. 

(15 m)

2000 (610)

2000 (610)

50 ft. 

(15 m)

2

802.3af

6.49

37

2000 (610)

2000 (610)

3

802.3af

12.95

37

1798 (548)

1303 (397)

4

802.3at

25.5

42

1263 (385)

914 (279)

5

802.3bt

N/A

N/A

N/A

N/A

N/A

N/A

6

802.3bt

N/A

N/A

N/A

N/A

N/A

N/A

Table 3: 1-port (POEXTX1) Transmitter powered by a 60 W External Power Supply (such as POWER-60W) plugged into the Transmitter 

(assuming 55 VDC output). 

No Additional External Power Source for the Receiver.

Summary of Contents for C13CORD-B













Reviews: