background image

6

Installation Guide

AT-DISP-CTRL

IP Configuration

1.  Make sure the AT-DISP-CTRL is powered
2.  Press and hold the 

IP MODE

 button, on the rear of the unit, for approximately five seconds.  

The AT-DISP-CTRL is shipped with DHCP enabled.  Once connected to a network, the DHCP 

server (if available), will automatically assign an IP address to the unit.  If the AT-DISP-CTRL 

is unable to detect a DHCP server within 15 seconds, then the unit will use a self-assigned IP 

address within the range of 

169.254.xxx.xxx

.

Use an IP scanner, along with the MAC address on the bottom of the unit, to identify the unit on 

the network.  If a static IP address is desired, the unit can be switched to static IP mode. 

The default static IP address is 

192.168.1.254

.

Switching the IP mode

IP MODE LED flashes

Description

Two

Factory Static IP mode (IP address set to 

192.168.1.254

)

Four

DHCP mode

3.  Release the button once the LED indicator, next to the 

IP MODE

 button, begins to flash 

green.  The number of flashes will indicate the currently selected IP mode.

HDMI IN

HDMI OUT

SOURCE

POWER

AT-DISP-CTRL

AT-DISP-CTRL

LAN

RX

PoE

TX

TX

RESET

IP MODE

RS-232 IR OUT

DC 5V

FW

IP Mode button

To display the IP address of the AT-DISP-CTRL, on the connected display, press and release the 

IP MODE

 button.  

Displaying the IP Address

Summary of Contents for Atlona AT-DISP-CTRL













Reviews: