manualshive.com logo in svg

Pandora Light, Manual, Page: 40 / 52

Share
Download
Pandora Light Manual Download Page 40

40

Security-service system Pandora Light

Preparing to program the system using a computer

The system allows programming all settings and updating software of the base unit via a micro-USB 

cable. If the base unit has not been installed in the vehicle yet, it will be powered via a micro-USB cable 

while programming. To program using a computer, you need a standard USB cable, a computer with 

the Windows XP/Vista/7/8/10 and the Pandora Alarm Studio application (you can download it from 

pandorainfo.com).

It is required to create an account in the Alarm Studio to use the Pandora CLONE for the remote 

engine start (you can register without a connection to a system). The Pandora CLONE procedure 

requires an Internet connection.

In preparation to programming, the following steps should be followed:

•  Connect the system with a PC using a USB cable;

•  Run the Pandora Alarm Studio

•  Enter the programming menu by entering the service PIN-code.

•  The application will automatically find the system.

Updating firmware

It is recommended to update firmware of the base unit before installing and programming the 

system. You can update firmware using the Alarm Studio application after entering programming 

mode or using quick boot algorithm (the PIN-code is not required).

Quick boot mode: open the Alarm Studio; de-energize and disconnect the system; press and 

hold the VALET button located on the base unit; release the button immediately after connecting the 

system and a computer via USB cable; the system will enter boot mode.

ATTENTION! If the boot mode has been interrupted for some reason and the status 

indicator lights red, you need to load firmware using quick boot mode (without 

entering the PIN-code). 

Programming using the VALET button

The system allows programming some settings using the VALET button. To configure all settings use 

a computer to program the system.

Enter the programming mode by entering the “Service PIN-code”, Use the VALET button to enter the 

desired level number (press the button a number of times, equals to the level number; pauses between 

presses should not exceed 1 second). The system will confirm correct input with red LED flashes and 

short sound signals of a siren and proceed to the desired level. If the input was incorrect, the system will 

not confirm input and will await a new level input after a series of green and red flashes.

Summary of Contents for Light





















































Reviews:

No comments