Panasonic Y5B Operation Manual Download Page 17

Page: 17 / 20

Guide for Getting FPC connector Y5B and Y5BW

Panasonic Corporation
industrial.panasonic.com/ac/e/

Panasonic Corporation 2015

ACCTF15E-3 201507

- 16 -

07-4. Detailed precautions for solder rework

(1) Flux-applying tool

To prevent solder creeping to a contact section,
we recommend the use of a brush pen that can
apply an appropriate amount of flux.
(e.g., BON-102F, Japan Bonkote)

(2) Selection of soldering iron

For FPC connector with 0.3-mm pitch, we recommend:

- An iron tip with a

retractable-knife shape

Ex. Japan Bonkote

- With a temperature sensor on the iron tip
- Temperature-controllable iron tip

It is also necessary to check that there are no differences between the indicated
temperature and the actual temperature of the iron tip.

The following temperatures are recommended for iron tips:
- Eutectic solder: 300–

320˚C

- Lead-free solder of three elements: 340–

360˚C

Conventional tool: Dropper

Recommended: Brush pen

Summary of Contents for Y5B





















Search results

Summary of Contents for Y5B

Reviews:

Related manuals for Y5B

Brands by name

Popular brands

Panasonic Y5B, Operation Manual

Search results

Summary of Contents for Y5B

Reviews:

Related manuals for Y5B

Brands by name

Popular brands